TC-FOOTPRINT-PCB · Demo Board for Tag-Connect Footprints

Everything you need to try the Tag-Connect approach on your own board: cable, adapter to the 20-pin ARM header, both retainers, protective cap and a demo board with the footprints to hold in your hand. Put together so that nothing is missing and nothing is doubled.

Connects a 6-pin Plug-of-Nails™ target (legged) to a 10-pin 2.54 mm (0.1″) IDC socket, for select Altera USB Blaster/ByteBlaster programmers.

Connects a 6-pin Plug-of-Nails™ target (no legs) to a 10-pin 2.54 mm (0.1″) IDC socket, for select Altera USB Blaster/ByteBlaster programmers.

6-pin TC2030 Plug-of-Nails™ cable, legged, for ARM Cortex targets. 10-pin ribbon connector on 1.27 mm (0.05″) in FTSH-105 format (Cortex Debug standard, e.g. Keil ULINK2).

6-pin TC2030 cable with legs and a 20-pin 1.27 mm connector — for debuggers with the ARM Cortex Debug+ETM port: IAR I-Jet, Keil ULINK Pro, SEGGER J-Trace. Electrically identical to the TC2030-CTX; only the debugger-side connector differs.

6-pin TC2030 cable without legs and with a 20-pin 1.27 mm connector for IAR I-Jet, Keil ULINK Pro and SEGGER J-Trace. For boards that should not get leg holes, and for connections that last longer than one programming cycle.

6-pin TC2030-NL Plug-of-Nails™ programming cable, no legs, for ARM Cortex targets. 10-pin ribbon connector on 1.27 mm (0.05″) in FTSH-105 format, saves over 66% board area versus classic FTSH-105 micro-headers.

6-pin TC2030-NL Plug-of-Nails™ cable, no legs, for ARM Cortex targets — with the 10-pin 1.27 mm (0.05″) ribbon connector fitted reversed at the factory, specifically for Atmel-ICE.

6-pin TC2030-NL cable, no legs, for STM32 targets with STLINK-V3/STLINK-V3MINI. 14-pin ribbon connector on 1.27 mm (0.05″) in STDC14 (FTSH-107) format, carries SWD including the SWO signal.

6-pin TC2030 cable, legged, for STM32 targets with STLINK-V3/STLINK-V3MINI. 14-pin ribbon connector on 1.27 mm (0.05″) in STDC14 (FTSH-107) format, carries SWD including the SWO signal.

FTDI TTL-232R-3V3 USB-to-serial cable fitted with a TC2030 6-pin legged Tag- Connector. USB-A plug at the other end. No mating connector needed on the target board.

FTDI TTL-232RG-VIP USB-to-serial cable fitted with a TC2030 6-pin legged Tag- Connector. USB-A plug at the other end. No mating connector needed on the target board.

6-pin Plug-of-Nails™ cable, legged, with a 6-pin 2.54 mm (0.1″) ribbon connector to the host. Snaps directly into a tiny PCB footprint — no mating connector needed on the target board.

Like TC2030-IDC — six contacts on the board, 6-pin 2.54 mm (0.1″) connector at the debugger — but 254 mm (10″) instead of the standard length — for extra distance between debugger and target board.

6-pin Plug-of-Nails™ cable, no legs, with a 6-pin 2.54 mm (0.1″) ribbon connector. Footprint about the size of an 0805 SMT resistor.

Like TC2030-IDC-NL — six contacts on the board, 6-pin 2.54 mm (0.1″) connector at the debugger — but 254 mm (10″) instead of the standard length.

Connects a 6-pin Plug-of-Nails™ target (legged) via an RJ12 modular connector to a Microchip ICD programmer.

Like TC2030-MCP — six contacts on the board, RJ12 modular plug at the programmer — but 254 mm (10″) instead of the standard length.

Connects a 6-pin Plug-of-Nails™ target (no legs) via an RJ12 modular connector to a Microchip ICD programmer. Footprint barely bigger than an SMT resistor.

Like TC2030-MCP-NL — six contacts on the board, RJ12 modular plug at the programmer — but 254 mm (10″) instead of the standard length.

Connects a 6-pin Plug-of-Nails™ target (legged) to Microchip's PICkit 3/4/5, via a 6-pin 2.54 mm (0.1″) SIP header.

Connects a 6-pin Plug-of-Nails™ target (no legs) to Microchip's PICkit 3/4/5 — through a single-row 6-pin header on 2.54 mm (0.1″). Footprint barely bigger than an SMT resistor.

Ten-pin debug and programming cable with spring pins that lands straight on the board — no connector on the target, just ten contact pads and six holes. The four legs hold it there while you work. At the other end, a standard 2.54 mm (0.1″) ribbon header that fits nearly every debugger.

10-pin Plug-of-Nails™ cable (legged) to 1.27 mm (0.05″) pitch ribbon, for ULINK2 and similar debuggers with Samtec FTSH-105-01 style micro-headers. All 10 pins connected (unlike the standard TC2050-IDC-050, which leaves pins 5/9 open for ARM compatibility).

10-contact legged programming cable for TI's MSP-FET430 debugger and its 14-pin 2.54 mm (0.1″) connector, compatible with all MSP430 microcontrollers — direct contact with no mating connector needed on the target board.

Ten-pin debug and programming cable with spring pins, without legs — the smallest debug access a board can have: ten contact pads and three holes, nothing else. At the other end a standard 2.54 mm (0.1″) ribbon header.

Like TC2050-IDC-NL-050, but with all 10 pins connected instead of leaving pins 5/9 open. No legs, for ULINK2 and similar debuggers with Samtec FTSH-105-01 style micro-headers on 1.27 mm (0.05″).

10-pin Plug-of-Nails™ cable, no legs, with a 14-pin 1.27 mm (0.05″) ribbon connector in STDC14 format for STLINK-V3/STLINK-V3MINI.

10-contact spring-pin cable, no Legs, for TI's MSP-FET430 debugger and its 14-pin 2.54 mm (0.1″) connector, compatible with all MSP430 microcontrollers.

14-pin Plug-of-Nails™ cable, legged, terminating in a 14-pin (2×7) 2.54 mm (0.1″) ribbon connector.

14-pin Plug-of-Nails™ cable with legs, terminating in a **1.27 mm (0.05″) pitch** connector — the slim variant for debuggers with a fine IDC header.

14-pin Plug-of-Nails™ cable, no legs, terminating in a 2.54 mm (0.1″) IDC ribbon connector (2×7 pin).

14-pin Plug-of-Nails™ cable without legs and with a 14-pin 1.27 mm (0.05″) IDC connector — all 14 pins connected. Plugs straight into the STDC14 port of ST-LINK V3, V3SET and V3MINI and brings the ST-LINK's Virtual COM Port to the board alongside SWD and JTAG.