TC2050-IDC-NL-430 · Cable for TI MSP-FET430
€50.00
- From 1 pcs: €50.00 / pc
- From 20 pcs: €46.00 / pc
- From 30 pcs: €45.00 / pc
Available in 7 days, delivery time 1-3 days
Product information "TC2050-IDC-NL-430 · Cable for TI MSP-FET430"
Short description
10-contact spring-pin cable, no Legs, for TI's MSP-FET430 debugger and its 14-pin 2.54 mm (0.1″) connector, compatible with all MSP430 microcontrollers.
Connections
| Side | Pins | Connector | Pitch |
|---|---|---|---|
| Board (Tag-Connect) | 10 | Footprint TC2050, no Legs | 1.27 mm (0.05″) |
| Debugger | 14 | Socket TI MSP-FET430, 2 × 7 | 2.54 mm (0.1″) |
Pin assignment: contacts 1–9 on pins 1–9, contact 10 on pin 11 — the full table is in the "Technical data" tab. Assignment measured by us — not yet documented by the manufacturer.
Compatible: TI MSP-FET430 in JTAG and Spy-Bi-Wire mode.
Not, or not directly, compatible
- 14-pin, 2 × 7, 1.27 mm (0.05″) — STDC14, e.g. ST-LINK V3: TC2050-IDC-NL-050-STDC14
- 10-pin, 2 × 5, 1.27 mm (0.05″) — Cortex connector, e.g. Keil ULINK2: TC2050-IDC-NL-050-ALL
- 10-pin, 2 × 5, 2.54 mm (0.1″) — e.g. PEmicro Multilink, USB-Blaster: TC2050-IDC-NL
Technical data
- PCB footprint: 0.03 sq. in.
- Spring pins: rated for over 100,000 operations
- Version: no legs
In use with these devices
TI MSP-FET430 debugger · all MSP430 microcontrollers (JTAG or SPY-BI-WIRE)
What counts is the connector, not the device name: compare the connector on your device with the table above. If it carries a different one, the route goes through an adapter board.
Note
Optional fixation with a TC2050-CLIP board. For self-securing mounting, use the legged variant TC2050-IDC-430.
Variants
TC2050-IDC-430 — legged. TC2030-MCP-NL — 6-pin alternative, smaller footprint. TC2050-IDC-NL — standard 10-pin version.
| Bauform: | IDC-Kabelende, NL (No Legs) |
|---|
Manufacturer's datasheet (PDF, copy hosted by us)
Pin assignment
| MSP-FET430 | Signal | TC2050 |
|---|---|---|
| 1 | VCC | 1 |
| 2 | TDI | 2 |
| 3 | TDO | 3 |
| 4 | TMS | 4 |
| 5 | TCK | 5 |
| 6 | VCC2 | 6 |
| 7 | GND | 7 |
| 8 | GND | 8 |
| 9 | RST / NMI | 9 |
| 11 | TEST | 10 |
Not connected: 10, 12, 13, 14.
Contacts 1 to 9 sit on pins 1 to 9; only the tenth contact jumps to pin 11.
Assignment measured by us — not yet documented by the manufacturer. The measurement was taken on the TC2050-IDC-430; this article has the same cable internals.
Accessories
Protective cap for the 10-pin TC2050 cable family (Plug-of-Nails™). Protects spring contacts, steel guide pins and — where present — retention tabs during storage and transport.
- from 1 pcs €5.00
- from 20 pcs €4.60
- from 30 pcs €4.50
Temporarily holds a TC2050-NL cable in place on the target board — for hands-free programming or debugging where board space is tight. 3-pack.
- from 1 pcs €22.00
- from 20 pcs €20.24
- from 30 pcs €19.80
Holds a TC2050-NL cable permanently against the target board — 3-pack.
- from 1 pcs €14.00
- from 20 pcs €12.88
- from 30 pcs €12.60
Demo board carrying every Tag-Connect footprint size, for comparison before laying out your own board — 6-, 10- and 14-pin, each with and without legs, plus the EC-10 Edge-Connect™ footprint.
- from 1 pcs €2.00
- from 20 pcs €1.84
- from 30 pcs €1.80
Related products
10-contact legged programming cable for TI's MSP-FET430 debugger and its 14-pin 2.54 mm (0.1″) connector, compatible with all MSP430 microcontrollers — direct contact with no mating connector needed on the target board.
- from 1 pcs €50.00
- from 20 pcs €46.00
- from 30 pcs €45.00
14-pin Plug-of-Nails™ cable, legged, terminating in a 14-pin (2×7) 2.54 mm (0.1″) ribbon connector.
- from 1 pcs €65.00
- from 20 pcs €59.80
- from 30 pcs €58.50
14-pin Plug-of-Nails™ cable, no legs, terminating in a 2.54 mm (0.1″) IDC ribbon connector (2×7 pin).
- from 1 pcs €65.00
- from 20 pcs €59.80
- from 30 pcs €58.50
14-pin Edge-Connect™ with two guide pins, terminating in a **2.54 mm (0.1″) IDC header** — the classic ribbon connector on a 2.54 mm pitch.
- from 1 pcs €92.00
Hersteller: Tag-Connect, LLC, 433 Airport Blvd, Suite 323, Burlingame, CA 94010, USA. Tel. +1 877-244-4156 · support@tag-connect.com
Verantwortliche Person in der EU (Art. 19 GPSR, da Hersteller ohne EU-Niederlassung):
Collion GmbH & Co.KG
Am Schmiedlacker 56, D-84028 Landshut
Tel. +49 (871) 2066-1000 · info@collion.de