SWD - ARM Cortex / RISC-V
Connects a TC2030-IDC or TC2030-IDC-NL cable to a 20-pin ARM SWD target. Also works when the target board carries a 6-pin 2.54 mm (0.1″) IDC header instead of the classic 20-pin header.
- from 1 pcs €38.00
- from 20 pcs €34.96
- from 30 pcs €34.20
Adapter board from the 20-pin ARM debugger connector (2 × 10 pin, 2.54 mm) to 6 pin (2 × 3, 2.54 mm) for TC2030-IDC, TC2030-IDC-NL and ECV3-06-IDC. The debug lines run through series resistors; every signal is brought out individually for probing.
- from 1 pcs €30.00
- from 2 pcs €28.50
- from 3 pcs €27.00
- from 5 pcs €25.50
- from 10 pcs €24.00
Adapter board from the 20-pin ARM debugger connector (2 × 10 pin, 2.54 mm) to the 14-pin 1.27 mm (0.05″) connector (1.27 mm) used by the ST-LINK V3 and by Tag-Connect's STDC14 cables. The debug lines run through series resistors; every signal is brought out individually for probing.
- from 1 pcs €30.00
- from 20 pcs €27.60
- from 30 pcs €27.00
Edge-Connect™ cable with six contacts at the board edge, terminating in the **ARM Cortex debug connector** — the 10-pin 1.27 mm (0.05″) header carried by Keil ULINK2 and most Cortex debuggers.
- from 1 pcs €85.00
- from 20 pcs €78.20
- from 30 pcs €76.50
Edge-Connect™ cable with six contacts at the board edge, terminating in the **STDC14 header** — the 14-pin connector on ST's STLINK-V3 and STLINK-V3MINI debuggers.
- from 1 pcs €85.00
- from 20 pcs €78.20
- from 30 pcs €76.50
Edge-Connect™ connector for direct board-edge contact — no mating connector on the target board, just one locating hole. Terminates in a 6-pin 2.54 mm (0.1″) IDC ribbon connector.
- from 1 pcs €85.00
- from 20 pcs €78.20
- from 30 pcs €76.50
Third-generation Edge-Connect™ connector for direct board-edge contact, terminating in a 10-pin 2.54 mm (0.1″) IDC ribbon connector. No mating connector on the target board — just one locating hole, and a low profile suited to stacked boards.
- from 1 pcs €88.00
- from 20 pcs €80.96
- from 30 pcs €79.20
Edge-Connect™ board-edge connector, terminating in a 10-pin 1.27 mm (0.05″) IDC ribbon connector. Fits debuggers with Samtec FTSH-105-01 style micro-headers (e.g. ULINK2).
- from 1 pcs €88.00
- from 20 pcs €80.96
- from 30 pcs €79.20
Edge-Connect™ cable with a 10-pin ECV3 board-edge connector, terminating in a 20-pin 1.27 mm (0.05″) ribbon connector. Fits ULINK2 and similar debuggers using Samtec FTSH-110-01 style micro-headers.
- from 1 pcs €88.00
- from 20 pcs €80.96
- from 30 pcs €79.20
Edge-Connect™ cable with ten contacts at the board edge, terminating in the **STDC14 header** — the 14-pin connector on ST's STLINK-V3 and STLINK-V3MINI debuggers. Carries JTAG **and** SWD.
- from 1 pcs €88.00
- from 20 pcs €80.96
- from 30 pcs €79.20
14-pin Edge-Connect™ with two guide pins, terminating in the **20-pin Cortex-20 header** and carrying the trace signals.
- from 1 pcs €92.00
- from 20 pcs €84.64
- from 30 pcs €82.80
14-pin Edge-Connect™ with two guide pins, terminating in a **1.27 mm (0.05″) IDC header** — the narrow ribbon connector on a 1.27 mm pitch.
- from 1 pcs €92.00
- from 20 pcs €84.64
- from 30 pcs €82.80
6-pin TC2030 Plug-of-Nails™ cable, legged, for ARM Cortex targets. 10-pin ribbon connector in FTSH-105 format (Cortex Debug standard, e.g. Keil ULINK2).
- from 1 pcs €50.00
- from 20 pcs €46.00
- from 30 pcs €45.00
6-pin TC2030 cable with legs and a 20-pin 1.27 mm connector — for debuggers with the ARM Cortex Debug+ETM port: IAR I-Jet, Keil ULINK Pro, SEGGER J-Trace. Electrically identical to the TC2030-CTX; only the debugger-side connector differs.
- from 1 pcs €55.00
- from 20 pcs €50.60
- from 30 pcs €49.50
6-pin TC2030 cable without legs and with a 20-pin 1.27 mm connector for IAR I-Jet, Keil ULINK Pro and SEGGER J-Trace. For boards that should not get leg holes, and for connections that last longer than one programming cycle.
- from 1 pcs €55.00
- from 20 pcs €50.60
- from 30 pcs €49.50
6-pin TC2030-NL Plug-of-Nails™ programming cable, no legs, for ARM Cortex targets. 10-pin ribbon connector in FTSH-105 format, saves over 66% board area versus classic FTSH-105 micro-headers.
- from 1 pcs €50.00
- from 20 pcs €46.00
- from 30 pcs €45.00
6-pin TC2030-NL Plug-of-Nails™ cable, no legs, for ARM Cortex targets — with the 10-pin ribbon connector fitted reversed at the factory, specifically for Atmel-ICE.
- from 1 pcs €50.00
- from 20 pcs €46.00
- from 30 pcs €45.00
6-pin TC2030-NL cable, no legs, for STM32 targets with STLINK-V3/STLINK-V3MINI. 14-pin ribbon connector in STDC14 (FTSH-107) format, carries SWD including the SWO signal.
- from 1 pcs €50.00
- from 20 pcs €46.00
- from 30 pcs €45.00
6-pin TC2030 cable, legged, for STM32 targets with STLINK-V3/STLINK-V3MINI. 14-pin ribbon connector in STDC14 (FTSH-107) format, carries SWD including the SWO signal.
- from 1 pcs €50.00
- from 20 pcs €46.00
- from 30 pcs €45.00
6-pin Plug-of-Nails™ cable, legged, with a 6-pin 2.54 mm (0.1″) ribbon connector to the host. Snaps directly into a tiny PCB footprint — no mating connector needed on the target board.
- from 1 pcs €40.00
- from 20 pcs €36.80
- from 30 pcs €36.00
Like TC2030-IDC, but 254 mm (10″) instead of the standard length — for extra distance between debugger and target board.
- from 1 pcs €40.00
- from 20 pcs €36.80
- from 30 pcs €36.00
6-pin Plug-of-Nails™ cable, no legs, with a 6-pin 2.54 mm (0.1″) ribbon connector. Footprint about the size of an 0805 SMT resistor.
- from 1 pcs €40.00
- from 20 pcs €36.80
- from 30 pcs €36.00
Like TC2030-IDC-NL, but 254 mm (10″) instead of the standard length.
- from 1 pcs €40.00
- from 20 pcs €36.80
- from 30 pcs €36.00
Adapter that makes TC2050-IDC cables usable for ARM JTAG and ARM SWD applications — converts 20-pin to 10-pin IDC.
- from 1 pcs €40.00
- from 20 pcs €36.80
- from 30 pcs €36.00