ECV3-10-IDC-050-20 · Edge-Connect™ Cable for ULINK2
€88.00
- From 1 pcs: €88.00 / pc
Available, delivery time: 1-3 days
Only 2 left in stock
Product information "ECV3-10-IDC-050-20 · Edge-Connect™ Cable for ULINK2"
Short description
Edge-Connect™ cable with a 10-pin ECV3 board-edge connector, terminating in a 20-pin 1.27 mm (0.05″) ribbon connector. Fits ULINK2 and similar debuggers using Samtec FTSH-110-01 style micro-headers.
Connections
| Side | Pins | Connector | Pitch |
|---|---|---|---|
| Board (Tag-Connect) | 10 | Edge contacts ECV3-10 (Edge-Connect™) | 1.27 mm (0.05″) |
| Debugger | 20 | Socket Keil ULINK2, 2 × 10 | 1.27 mm (0.05″) |
Pin assignment: contacts 1–10 on pins 1–10; pins 11–20 stay free — the full table is in the "Technical data" tab. Assignment measured by us — not yet documented by the manufacturer.
Compatible: Keil ULINK2 at its 20-pin 1.27 mm connector.
Not, or not directly, compatible
- 10-pin, 2 × 5, 1.27 mm (0.05″) — Cortex connector, e.g. Keil ULINK2: ECV3-10-IDC-050
- 10-pin, 2 × 5, 2.54 mm (0.1″) — e.g. PEmicro Multilink, USB-Blaster: ECV3-10-IDC
- 14-pin, 2 × 7, 1.27 mm (0.05″) — STDC14, e.g. ST-LINK V3: ECV3-10-IDC-STDC14
Easily confused: The classic 20-pin ARM connector has the same pin count at twice the pitch.
Technical data
- Ribbon pitch: 1.27 mm (0.05″)
In use with these devices
IAR I-JET (ARM JTAG/SWD) · ARM Keil ULINK Pro (ARM JTAG/SWD) · Cortex-20/MIPI-20 generic debuggers (ARM JTAG/SWD) · Renesas E1/E2/E8a/E20 (via ARM20 adapter)
What counts is the connector, not the device name: compare the connector on your device with the table above. If it carries a different one, the route goes through an adapter board.
Included
Ribbon cable and Microchip PICkit 4 connector. Not included: demo PCB.
| Bauform: | ECV3 Edge Connector, IDC-Kabelende |
|---|
Datasheet with our advisory note (PDF — manufacturer's drawing with a note from us in front)
Pin assignment
| ULINK2 | Signal | ECV3-10 |
|---|---|---|
| 1 | VREF (VTREF) | 1 |
| 2 | TMS_SWDIO | 2 |
| 3 | GND | 3 |
| 4 | TCK_SWCLK | 4 |
| 5 | GND | 5 |
| 6 | TDO_SWO_TRACE_CTL | 6 |
| 7 | KEY | 7 |
| 8 | TDI | 8 |
| 9 | GND | 9 |
| 10 | nRESET | 10 |
Not connected: 11 to 20 — the trace lines of the 20-pin connector.
The ten edge contacts sit 1:1 on pins 1 to 10 — the signal set of the 10-pin Cortex connector. The upper half of the 20-pin header stays free.
Assignment measured by us — not yet documented by the manufacturer.
Accessories
A small board carrying the Edge-Connect™ footprints at full size — to handle, measure and try out before you commit the pattern to your own layout. The V3 denotes the third generation of the Edge-Connect series — the same one the ECV3 cables belong to.
- from 1 pcs €2.00
Related products
Third-generation Edge-Connect™ connector for direct board-edge contact, terminating in a 10-pin 2.54 mm (0.1″) IDC ribbon connector. No mating connector on the target board — just one locating hole, and a low profile suited to stacked boards.
- from 1 pcs €88.00
- from 20 pcs €80.96
- from 30 pcs €79.20
Edge-Connect™ board-edge connector, terminating in a 10-pin 1.27 mm (0.05″) IDC ribbon connector. Fits debuggers with Samtec FTSH-105-01 style micro-headers (e.g. ULINK2).
- from 1 pcs €88.00
Edge-Connect™ cable with ten contacts at the board edge, terminating in the
- from 1 pcs €88.00
6-pin TC2030 cable with legs and a 20-pin 1.27 mm connector — for debuggers with the ARM Cortex Debug+ETM port: IAR I-Jet, Keil ULINK Pro, SEGGER J-Trace. Electrically identical to the TC2030-CTX; only the debugger-side connector differs.
- from 1 pcs €55.00
6-pin TC2030 cable without legs and with a 20-pin 1.27 mm connector for IAR I-Jet, Keil ULINK Pro and SEGGER J-Trace. For boards that should not get leg holes, and for connections that last longer than one programming cycle.
- from 1 pcs €55.00
14-pin Edge-Connect™ with two guide pins, terminating in the **20-pin Cortex-20 header on 1.27 mm (0.05″)** and carrying the trace signals.
- from 1 pcs €92.00
Hersteller: Tag-Connect, LLC, 433 Airport Blvd, Suite 323, Burlingame, CA 94010, USA. Tel. +1 877-244-4156 · support@tag-connect.com
Verantwortliche Person in der EU (Art. 19 GPSR, da Hersteller ohne EU-Niederlassung):
Collion GmbH & Co.KG
Am Schmiedlacker 56, D-84028 Landshut
Tel. +49 (871) 2066-1000 · info@collion.de