SoC / MCU (SWD/JTAG)

Adapter board between the 20-pin ARM connector on your debugger (2 × 10, 2.54 mm / 0.1″) and a TC2030-IDC or TC2030-IDC-NL cable — for ARM SWD. The 20-pin connector goes to the debugger, not to the target board.

Adapter board from the 20-pin ARM debugger connector (2 × 10 pin, 2.54 mm) to 6 pin (2 × 3, 2.54 mm) for the Plug-of-Nails™ cables TC2030-IDC and TC2030-IDC-NL, and for ECV3-06-IDC. The debug lines run through series resistors; every signal is brought out individually for probing.

Adapter board between the 20-pin ARM debug header (2 × 10, 2.54 mm) and the ten-pin IDC connector of the TC2050 Plug-of-Nails™ cables. With series resistors, plug-in jumpers for supply and nTRST, measuring points and the pinout printed on the board.

Adapter board from the 20-pin ARM debugger connector (2 × 10 pin, 2.54 mm) to the 14-pin 1.27 mm (0.05″) connector (1.27 mm) used by the ST-LINK V3 and by Tag-Connect's STDC14 cables (Plug-of-Nails™). The debug lines run through series resistors; every signal is brought out individually for probing.

Adapter board with a pin header for the debugger's 20-pin ribbon cable (2 × 10 pin, 2.54 mm) to 6 pin (2 × 3, 2.54 mm) for the Plug-of-Nails™ cables TC2030-IDC and TC2030-IDC-NL, and for ECV3-06-IDC. For devices whose 20-pin connector is not freely accessible. The debug lines run through series resistors; every signal is brought out individually for probing.

Edge-Connect™ cable with six contacts at the board edge, terminating in the **ARM Cortex debug connector** — the 10-pin 1.27 mm (0.05″) header carried by Keil ULINK2 and most Cortex debuggers.

Edge-Connect™ cable with six contacts at the board edge, terminating in the

Edge-Connect™ connector for direct board-edge contact — no mating connector on the target board, just one locating hole. Terminates in a 6-pin 2.54 mm (0.1″) IDC ribbon connector.

Third-generation Edge-Connect™ connector for direct board-edge contact, terminating in a 10-pin 2.54 mm (0.1″) IDC ribbon connector. No mating connector on the target board — just one locating hole, and a low profile suited to stacked boards.

Edge-Connect™ board-edge connector, terminating in a 10-pin 1.27 mm (0.05″) IDC ribbon connector. Fits debuggers with Samtec FTSH-105-01 style micro-headers (e.g. ULINK2).

Edge-Connect™ cable with a 10-pin ECV3 board-edge connector, terminating in a 20-pin 1.27 mm (0.05″) ribbon connector. Fits ULINK2 and similar debuggers using Samtec FTSH-110-01 style micro-headers.

Edge-Connect™ cable with ten contacts at the board edge, terminating in the

14-pin Edge-Connect™ with two guide pins, terminating in the **20-pin Cortex-20 header on 1.27 mm (0.05″)** and carrying the trace signals.

14-pin Edge-Connect™ with two guide pins, terminating in a **1.27 mm (0.05″) IDC header** — the narrow ribbon connector on a 1.27 mm pitch.

6-pin TC2030 Plug-of-Nails™ cable, legged, for ARM Cortex targets. 10-pin ribbon connector on 1.27 mm (0.05″) in FTSH-105 format (Cortex Debug standard, e.g. Keil ULINK2).

6-pin TC2030 cable with legs and a 20-pin 1.27 mm connector — for debuggers with the ARM Cortex Debug+ETM port: IAR I-Jet, Keil ULINK Pro, SEGGER J-Trace. Electrically identical to the TC2030-CTX; only the debugger-side connector differs.

6-pin TC2030 cable without legs and with a 20-pin 1.27 mm connector for IAR I-Jet, Keil ULINK Pro and SEGGER J-Trace. For boards that should not get leg holes, and for connections that last longer than one programming cycle.

6-pin TC2030-NL Plug-of-Nails™ programming cable, no legs, for ARM Cortex targets. 10-pin ribbon connector on 1.27 mm (0.05″) in FTSH-105 format, saves over 66% board area versus classic FTSH-105 micro-headers.

6-pin TC2030-NL Plug-of-Nails™ cable, no legs, for ARM Cortex targets — with the 10-pin 1.27 mm (0.05″) ribbon connector fitted reversed at the factory, specifically for Atmel-ICE.

6-pin TC2030-NL cable, no legs, for STM32 targets with STLINK-V3/STLINK-V3MINI. 14-pin ribbon connector on 1.27 mm (0.05″) in STDC14 (FTSH-107) format, carries SWD including the SWO signal.

6-pin TC2030 cable, legged, for STM32 targets with STLINK-V3/STLINK-V3MINI. 14-pin ribbon connector on 1.27 mm (0.05″) in STDC14 (FTSH-107) format, carries SWD including the SWO signal.

6-pin Plug-of-Nails™ cable, legged, with a 6-pin 2.54 mm (0.1″) ribbon connector to the host. Snaps directly into a tiny PCB footprint — no mating connector needed on the target board.

Like TC2030-IDC — six contacts on the board, 6-pin 2.54 mm (0.1″) connector at the debugger — but 254 mm (10″) instead of the standard length — for extra distance between debugger and target board.

6-pin Plug-of-Nails™ cable, no legs, with a 6-pin 2.54 mm (0.1″) ribbon connector. Footprint about the size of an 0805 SMT resistor.