ECV3-06-CTX · 6-pin Edge-Connect to Cortex-10
€85.00
- From 1 pcs: €85.00 / pc
Available, delivery time: 1-3 days
Only 1 left in stock
Product information "ECV3-06-CTX · 6-pin Edge-Connect to Cortex-10"
Short description
Edge-Connect™ cable with six contacts at the board edge, terminating in the ARM Cortex debug connector — the 10-pin 1.27 mm (0.05″) header carried by Keil ULINK2 and most Cortex debuggers.
Connections
| Side | Pins | Connector | Pitch |
|---|---|---|---|
| Board (Tag-Connect) | 6 | Edge contacts ECV3-06 (Edge-Connect™) | 1.27 mm (0.05″) |
| Debugger | 10 | Socket Cortex-10 (FTSH-105 style), 2 × 5 | 1.27 mm (0.05″) |
Full pin assignment: in the "Technical data" tab.
Compatible: Keil ULINK2, SEGGER J-Link and Atmel-ICE at the 10-pin 1.27 mm Cortex Debug connector (FTSH-105 style).
Not, or not directly, compatible
- 14-pin, 2 × 7, 1.27 mm (0.05″) — STDC14, e.g. ST-LINK V3: ECV3-06-CTX-STDC14
- 6-pin, 2 × 3, 2.54 mm (0.1″): ECV3-06-IDC
Easily confused: The 10-pin 2.54 mm box header looks similar — same pin count, twice the pitch. That is the most frequent mis-order.
Technical data
- Protocol: SWD
- Required on the target board: one non-plated locating hole
What you need it for
Edge-Connect places the contacts on the edge of the board rather than on its surface. The target board needs no mating connector at all — just the plated half-holes along the edge and one hole for location. That saves space and the cost of a component on every board you build.
Six contacts are enough for SWD. If you need JTAG or additional signals, use the 10-contact version.
The difference from the ECV3-06-IDC
Both cables have the same board side — the same six-contact edge pattern, the same locating hole. What differs is the other end: the ECV3-06-IDC carries a 6-pin 2.54 mm (0.1″) header, this one the 10-pin Cortex header on a 1.27 mm (0.05″) pitch.
So it is your debugger that decides, not your board. If in doubt, measure the pin spacing on your programmer: 2.54 mm means ECV3-06-IDC, 1.27 mm across ten pins means this cable.
In use with these devices
Cortex-10/MIPI-10 generic for ARM Cortex via SWD · ARM Keil ULINK2 · Cypress MiniProg 3 and 4 for PSoC · Atmel-ICE for SAM
What counts is the connector, not the device name: compare the connector on your device with the table above. If it carries a different one, the route goes through an adapter board.
Included
Cable with Edge-Connect™ connector and IDC header. The demo PCB shown in the manufacturer's photos is not included and is ordered separately.
Variants
ECV3-06-IDC — 6-pin 2.54 mm (0.1″) header. ECV3-06-CTX-STDC14 — for STLINK-V3 instead of Cortex-10. ECV3-10-IDC — ten contacts at the board edge.
On connector numbering: Why the six-pin Tag-Connect counts differently
| Form Factor: | ECV3 Edge Connector, IDC-Kabelende |
|---|
Datasheet with our advisory note (PDF — manufacturer's drawing with a note from us in front)
Pin assignment
| Cortex-10 | Signal | ECV3-06 |
|---|---|---|
| 1 | VCC | 1 |
| 2 | SWDIO / TMS | 2 |
| 3 | GND | 5 |
| 4 | SWCLK / TCK | 4 |
| 5 | GND | 5 |
| 6 | SWO / TDO | 6 |
| 9 | GNDDetect | 5 |
| 10 | nRESET | 3 |
Not connected: 7 (NC / RTCK), 8 (NC / TDI).
Same signal set as the TC2030-CTX; the board side is Edge-Connect instead of a footprint.
Pin assignment as specified by the manufacturer.
Accessories
A small board carrying the Edge-Connect™ footprints at full size — to handle, measure and try out before you commit the pattern to your own layout. The V3 denotes the third generation of the Edge-Connect series — the same one the ECV3 cables belong to.
- from 1 pcs €2.00
Storage case for Tag-Connect cables and accessories — the same one as in the TC2050 evaluation kit. Grey plastic case with carrying handle, a foam insert with compartments inside and convoluted foam in the lid. Room for one or two cables together with accessories such as an adapter, clip or grip.
- from 1 pcs €19.00
Related products
Edge-Connect™ connector for direct board-edge contact — no mating connector on the target board, just one locating hole. Terminates in a 6-pin 2.54 mm (0.1″) IDC ribbon connector.
- from 1 pcs €85.00
Edge-Connect™ cable with six contacts at the board edge, terminating in the
- from 1 pcs €85.00
6-pin TC2030 Plug-of-Nails™ cable, legged, for ARM Cortex targets. 10-pin ribbon connector on 1.27 mm (0.05″) in FTSH-105 format (Cortex Debug standard, e.g. Keil ULINK2).
- from 1 pcs €45.00
6-pin TC2030-NL Plug-of-Nails™ programming cable, no legs, for ARM Cortex targets. 10-pin ribbon connector on 1.27 mm (0.05″) in FTSH-105 format, saves over 66% board area versus classic FTSH-105 micro-headers.
- from 1 pcs €45.00
6-pin TC2030-NL Plug-of-Nails™ cable, no legs, for ARM Cortex targets — with the 10-pin 1.27 mm (0.05″) ribbon connector fitted reversed at the factory, specifically for Atmel-ICE.
- from 1 pcs €50.00
Edge-Connect™ board-edge connector, terminating in a 10-pin 1.27 mm (0.05″) IDC ribbon connector. Fits debuggers with Samtec FTSH-105-01 style micro-headers (e.g. ULINK2).
- from 1 pcs €88.00
10-pin Plug-of-Nails™ cable (legged) to 1.27 mm (0.05″) pitch ribbon, for ULINK2 and similar debuggers with Samtec FTSH-105-01 style micro-headers. All 10 pins connected (unlike the standard TC2050-IDC-050, which leaves pins 5/9 open for ARM compatibility).
- from 1 pcs €65.00
- from 20 pcs €59.80
- from 30 pcs €58.50
Like TC2050-IDC-NL-050, but with all 10 pins connected instead of leaving pins 5/9 open. No legs, for ULINK2 and similar debuggers with Samtec FTSH-105-01 style micro-headers on 1.27 mm (0.05″).
- from 1 pcs €65.00
- from 20 pcs €59.80
- from 30 pcs €58.50
Hersteller: Tag-Connect, LLC, 433 Airport Blvd, Suite 323, Burlingame, CA 94010, USA. Tel. +1 877-244-4156 · support@tag-connect.com
Verantwortliche Person in der EU (Art. 19 GPSR, da Hersteller ohne EU-Niederlassung):
Collion GmbH & Co.KG
Am Schmiedlacker 56, D-84028 Landshut
Tel. +49 (871) 2066-1000 · info@collion.de