Tiny tools for electronic development
Your Tag-Connect® supplier in Europe — since 2013
Collion® supplies Tag-Connect adapters for JTAG, SWD and ISP — spring pins instead of a soldered connector. Saves board space and unit cost.
Adapter board between the 20-pin ARM connector on your debugger (2 × 10, 2.54 mm / 0.1″) and a TC2030-IDC or TC2030-IDC-NL cable — for ARM SWD. The 20-pin connector goes to the debugger, not to the target board.
- from 1 pcs €29.00
Adapter board from the 20-pin ARM debugger connector (2 × 10 pin, 2.54 mm) to 6 pin (2 × 3, 2.54 mm) for the Plug-of-Nails™ cables TC2030-IDC and TC2030-IDC-NL, and for ECV3-06-IDC. The debug lines run through series resistors; every signal is brought out individually for probing.
- from 1 pcs €25.00
- from 3 pcs €24.00
- from 5 pcs €23.00
Adapter board between the 20-pin ARM debug header (2 × 10, 2.54 mm) and the ten-pin IDC connector of the TC2050 Plug-of-Nails™ cables. With series resistors, plug-in jumpers for supply and nTRST, measuring points and the pinout printed on the board.
- from 1 pcs €30.00
- from 3 pcs €24.00
- from 5 pcs €23.00
Adapter board from the 20-pin ARM debugger connector (2 × 10 pin, 2.54 mm) to the 14-pin 1.27 mm (0.05″) connector (1.27 mm) used by the ST-LINK V3 and by Tag-Connect's STDC14 cables (Plug-of-Nails™). The debug lines run through series resistors; every signal is brought out individually for probing.
- from 1 pcs €25.00
- from 3 pcs €24.00
- from 5 pcs €23.00
A small board carrying the Edge-Connect™ footprints at full size — to handle, measure and try out before you commit the pattern to your own layout. The V3 denotes the third generation of the Edge-Connect series — the same one the ECV3 cables belong to.
- from 1 pcs €2.00
Edge-Connect™ cable with six contacts at the board edge, terminating in the **ARM Cortex debug connector** — the 10-pin 1.27 mm (0.05″) header carried by Keil ULINK2 and most Cortex debuggers.
- from 1 pcs €85.00
Edge-Connect™ cable with six contacts at the board edge, terminating in the
- from 1 pcs €85.00
Edge-Connect™ connector for direct board-edge contact — no mating connector on the target board, just one locating hole. Terminates in a 6-pin 2.54 mm (0.1″) IDC ribbon connector.
- from 1 pcs €85.00
Third-generation Edge-Connect™ connector for direct board-edge contact, terminating in a 10-pin 2.54 mm (0.1″) IDC ribbon connector. No mating connector on the target board — just one locating hole, and a low profile suited to stacked boards.
- from 1 pcs €88.00
- from 20 pcs €80.96
- from 30 pcs €79.20
Edge-Connect™ board-edge connector, terminating in a 10-pin 1.27 mm (0.05″) IDC ribbon connector. Fits debuggers with Samtec FTSH-105-01 style micro-headers (e.g. ULINK2).
- from 1 pcs €88.00
Edge-Connect™ cable with a 10-pin ECV3 board-edge connector, terminating in a 20-pin 1.27 mm (0.05″) ribbon connector. Fits ULINK2 and similar debuggers using Samtec FTSH-110-01 style micro-headers.
- from 1 pcs €88.00
Edge-Connect™ cable with ten contacts at the board edge, terminating in the
- from 1 pcs €88.00
14-pin Edge-Connect™ with two guide pins, terminating in the **20-pin Cortex-20 header on 1.27 mm (0.05″)** and carrying the trace signals.
- from 1 pcs €92.00
14-pin Edge-Connect™ with two guide pins, terminating in a **2.54 mm (0.1″) IDC header** — the classic ribbon connector on a 2.54 mm pitch.
- from 1 pcs €92.00
14-pin Edge-Connect™ with two guide pins, terminating in a **1.27 mm (0.05″) IDC header** — the narrow ribbon connector on a 1.27 mm pitch.
- from 1 pcs €92.00
14-pin Edge-Connect™ with two guide pins, terminating in a **2 mm IDC header** — the pitch between 1.27 mm (0.05″) and 2.54 mm (0.1″).
- from 1 pcs €92.00
Holds a TC2050-NL cable permanently against the target board — 3-pack.
- from 1 pcs €14.00
Holds a TC2070-NL cable against the target board — 3-pack.
- from 1 pcs €14.00
Holds a TC2030-NL cable permanently against the target board — 3-pack.
- from 1 pcs €14.00
- from 20 pcs €12.88
- from 30 pcs €12.60
Prototyping board in the Arduino Mega footprint with a continuous ground plane. For prototype builds that outgrow the UNO format.
- from 1 pcs €3.50
Small prototyping board with a continuous ground plane, no Arduino footprint. For analog circuits on minimal board space.
- from 1 pcs €1.00
Prototyping board in the Arduino UNO footprint with a continuous ground plane. For compact, reliable prototype builds directly on the UNO.
- from 1 pcs €2.50
Protective cap for the 10-pin TC2050 cable family (Plug-of-Nails™). Protects spring contacts, steel guide pins and — where present — retention tabs during storage and transport.
- from 1 pcs €5.00
Protective cap for the 14-pin TC2070 cable family (Plug-of-Nails™). Protects spring contacts, steel guide pins and — where present — retention tabs during storage and transport.
- from 1 pcs €5.00
Tools for electronics development
Collion supplies industry and mid-sized manufacturers, engineering offices and freelancers, and institutions in training, education and research.
Shipped from our own warehouse in Germany. Usually within two working days of payment received. We ship within the EU, by DHL Priority.
Payment on account for companies and public bodies, once approved by us. We issue the invoice ourselves — with no payment service provider behind us and no credit agency enquiry. With payment on account and bank transfer in advance, your data stays with us. Details under Shipping and payment.
Including what you don't see here. The Tag-Connect range is larger than our shop catalogue. Items you cannot find here we source at the same terms, without a surcharge — a short message to info@collion.de is enough.