ARM20-CTX · 20-Pin ARM SWD Adapter for TC2030-IDC
€38.00
- From 1 pcs: €38.00 / pc
- From 20 pcs: €34.96 / pc
- From 30 pcs: €34.20 / pc
Available, delivery time: 1-3 days
More than 5 in stock
Product information "ARM20-CTX · 20-Pin ARM SWD Adapter for TC2030-IDC"
Short description
Adapter board between the 20-pin ARM connector on your debugger (2 × 10, 2.54 mm / 0.1″) and a TC2030-IDC or TC2030-IDC-NL cable — for ARM SWD. The 20-pin connector goes to the debugger, not to the target board.
Connections
| Side | Pins | Connector | Pitch |
|---|---|---|---|
| Debugger | 20 | Socket ARM-20, 2 × 10 | 2.54 mm (0.1″) |
| Cable (Tag-Connect) | 6 | Pin header, 2 × 3 | 2.54 mm (0.1″) |
Full pin assignment: in the "Technical data" tab.
Compatible: SEGGER J-Link, Keil ULINK, ST-LINK/V2 and the other debuggers using the classic 20-pin 2.54 mm ARM connector.
Not, or not directly, compatible
- 12-pin — Lattice HW-USBN-2B: through the adapter board TC-LATTICE
- 14-pin, 2 × 7, 2.54 mm (0.1″) — Renesas E1 / E2 / E8a / E20: through the adapter board TC-RENESAS
Easily confused: There is also a 20-pin Cortex connector on 1.27 mm (IAR I-Jet, Keil ULINK Pro, SEGGER J-Trace) — same pin count, half the pitch.
Technical data
- Compatibility: ARM SWD (Serial Wire Debug)
In use with these devices
ST STM32 with ST-LINK/V2 and ST-LINK V3 SET · ARM Cortex in general · PEmicro/P&E Multilink and Cyclone series · Segger J-LINK
What counts is the connector, not the device name: compare the connector on your device with the table above. If it carries a different one, the route goes through an adapter board.
Included
Adapter only. The TC2030-IDC or TC2030-IDC-NL cable is sold separately — the cable and Segger J-Link shown in product photos are not included.
| Bauform: | Legged |
|---|
Manufacturer's datasheet (PDF, copy hosted by us)
Pin assignment
| ARM-20 | Signal | TC2030 |
|---|---|---|
| 1 | VCC | 1 |
| 7 | SWDIO / TMS | 2 |
| 9 | SWCLK / TCK | 4 |
| 13 | SWO / TDO | 6 |
| 15 | nRESET | 3 |
| 4, 6, 8, 10, 12, 14, 16, 18, 20 | GND | 5 |
Not connected: 2, 17, 19 (NC), 3 (nTRST), 5 (TDI), 11 (RTCK) — JTAG signals a six-contact footprint cannot carry.
From the manufacturer datasheet (ARM20-CTX.pdf).
Accessories
Edge-Connect™ connector for direct board-edge contact — no mating connector on the target board, just one locating hole. Terminates in a 6-pin 2.54 mm (0.1″) IDC ribbon connector.
- from 1 pcs €85.00
6-pin Plug-of-Nails™ cable, legged, with a 6-pin 2.54 mm (0.1″) ribbon connector to the host. Snaps directly into a tiny PCB footprint — no mating connector needed on the target board.
- from 1 pcs €40.00
- from 20 pcs €36.80
- from 30 pcs €36.00
Like TC2030-IDC — six contacts on the board, 6-pin 2.54 mm (0.1″) connector at the debugger — but 254 mm (10″) instead of the standard length — for extra distance between debugger and target board.
- from 1 pcs €40.00
- from 20 pcs €36.80
- from 30 pcs €36.00
6-pin Plug-of-Nails™ cable, no legs, with a 6-pin 2.54 mm (0.1″) ribbon connector. Footprint about the size of an 0805 SMT resistor.
- from 1 pcs €40.00
- from 20 pcs €36.80
- from 30 pcs €36.00
Like TC2030-IDC-NL — six contacts on the board, 6-pin 2.54 mm (0.1″) connector at the debugger — but 254 mm (10″) instead of the standard length.
- from 1 pcs €40.00
- from 20 pcs €36.80
- from 30 pcs €36.00
Related products
Adapter board from the 20-pin ARM debugger connector (2 × 10 pin, 2.54 mm) to 6 pin (2 × 3, 2.54 mm) for TC2030-IDC, TC2030-IDC-NL and ECV3-06-IDC. The debug lines run through series resistors; every signal is brought out individually for probing.
- from 1 pcs €30.00
- from 2 pcs €28.50
- from 3 pcs €27.00
- from 5 pcs €25.50
- from 10 pcs €24.00
Adapter board between the 20-pin ARM debug header (2 × 10, 2.54 mm) and the ten-pin IDC connector of the TC2050 cables. With series resistors, plug-in jumpers for supply and nTRST, measuring points and the pinout printed on the board.
- from 1 pcs €30.00
Adapter board from the 20-pin ARM debugger connector (2 × 10 pin, 2.54 mm) to the 14-pin 1.27 mm (0.05″) connector (1.27 mm) used by the ST-LINK V3 and by Tag-Connect's STDC14 cables. The debug lines run through series resistors; every signal is brought out individually for probing.
- from 1 pcs €30.00
Adapter that makes TC2050-IDC cables usable for ARM JTAG and ARM SWD applications — converts the 20-pin ARM connector (2.54 mm / 0.1″) to a 10-pin header on the same pitch.
- from 1 pcs €30.00
- from 20 pcs €27.60
- from 30 pcs €27.00
Hersteller: Tag-Connect, LLC, 433 Airport Blvd, Suite 323, Burlingame, CA 94010, USA. Tel. +1 877-244-4156 · support@tag-connect.com
Verantwortliche Person in der EU (Art. 19 GPSR, da Hersteller ohne EU-Niederlassung):
Collion GmbH & Co.KG
Am Schmiedlacker 56, D-84028 Landshut
Tel. +49 (871) 2066-1000 · info@collion.de