TC2050-ARM2010 · 20-Pin Adapter for TC2050-IDC
€30.00
- From 1 pcs: €30.00 / pc
- From 20 pcs: €27.60 / pc
- From 30 pcs: €27.00 / pc
Available, delivery time: 1-3 days
Only 5 left in stock
Product information "TC2050-ARM2010 · 20-Pin Adapter for TC2050-IDC"
Short description
Adapter that makes TC2050-IDC cables usable for ARM JTAG and ARM SWD applications — converts the 20-pin ARM connector (2.54 mm / 0.1″) to a 10-pin header on the same pitch.
Connections
| Side | Pins | Connector | Pitch |
|---|---|---|---|
| Debugger | 20 | Socket ARM-20, 2 × 10 | 2.54 mm (0.1″) |
| Cable (Tag-Connect) | 10 | Pin header, 2 × 5 | 2.54 mm (0.1″) |
Full pin assignment: in the "Technical data" tab.
Compatible: SEGGER J-Link, Keil ULINK, ST-LINK/V2 and the other debuggers using the classic 20-pin 2.54 mm ARM connector.
Not, or not directly, compatible
- 12-pin — Lattice HW-USBN-2B: through the adapter board TC-LATTICE-10
- 14-pin, 2 × 7, 2 mm — Xilinx Platform Cable II: through the adapter board TC2050-XILINX
- 14-pin, 2 × 7, 2.54 mm (0.1″) — Renesas E1 / E2 / E8a / E20: through the adapter board TC-RENESAS
Easily confused: There is also a 20-pin Cortex connector on 1.27 mm (IAR I-Jet, Keil ULINK Pro, SEGGER J-Trace) — same pin count, half the pitch.
Technical data
- Application area: ARM JTAG, ARM SWD
In use with these devices
Segger J-LINK · ST-LINK/V2 · PEmicro/P&E Multilink variants (ACP, Universal/FX) · PEmicro/P&E Cyclone ARM and LC/FX Universal · ST-Link V3 SET
What counts is the connector, not the device name: compare the connector on your device with the table above. If it carries a different one, the route goes through an adapter board.
Included
Adapter only. Not included: debugger, cable.
Variants
TC2050-ARM2010-M — male variant for cable extension. ARM20-CTX — 20-pin to TC2030-IDC adapter for Cortex. TC2050-2X10 — 20-pin to dual 10-pin header.
| Bauform: | IDC-Kabelende |
|---|
Manufacturer's datasheet (PDF, copy hosted by us)
Pin assignment
| ARM-20 | Signal | TC2050 | JTAG | SWD |
|---|---|---|---|---|
| 1 | VCC | 1 | VCC | VCC |
| 3 | nTRST | 9 | nTRST | - |
| 5 | TDI | 8 | TDI | - |
| 7 | SWDIO / TMS | 2 | TMS | SWDIO |
| 9 | SWCLK / TCLK | 4 | TCK | SWCLK |
| 11 | RTCK | 7 | RTCK | - |
| 13 | SWO / TDO | 6 | TDO | SWO |
| 15 | RESET | 10 | RESET | RESET |
| 19 | +5 V (optional) | 5 | GND / +5 V | GND / +5 V |
| 4, 6, 8, 10, 12, 14, 16, 18, 20 | GND | 3 | GND | GND |
Not connected: 2, 17 (NC).
Pin 5 on the TC2050 side is selected by a solder bridge: ground, or supply from the debugger. Ground improves signal integrity. Pin 9 carries nTRST only when the second solder bridge is set. Some debuggers supply 3.3 V instead of 5 V.
From the manufacturer datasheet (TC2050-ARM2010.pdf).
Accessories
Third-generation Edge-Connect™ connector for direct board-edge contact, terminating in a 10-pin 2.54 mm (0.1″) IDC ribbon connector. No mating connector on the target board — just one locating hole, and a low profile suited to stacked boards.
- from 1 pcs €88.00
- from 20 pcs €80.96
- from 30 pcs €79.20
Ten-pin debug and programming cable with spring pins that lands straight on the board — no connector on the target, just ten contact pads and six holes. The four legs hold it there while you work. At the other end, a standard 2.54 mm (0.1″) ribbon header that fits nearly every debugger.
- from 1 pcs €40.00
- from 20 pcs €36.80
- from 30 pcs €36.00
Ten-pin debug and programming cable with spring pins, without legs — the smallest debug access a board can have: ten contact pads and three holes, nothing else. At the other end a standard 2.54 mm (0.1″) ribbon header.
- from 1 pcs €40.00
- from 20 pcs €36.80
- from 30 pcs €36.00
Related products
Adapter board between the 20-pin ARM connector on your debugger (2 × 10, 2.54 mm / 0.1″) and a TC2030-IDC or TC2030-IDC-NL cable — for ARM SWD. The 20-pin connector goes to the debugger, not to the target board.
- from 1 pcs €38.00
- from 20 pcs €34.96
- from 30 pcs €34.20
Adapter board from the 20-pin ARM debugger connector (2 × 10 pin, 2.54 mm) to 6 pin (2 × 3, 2.54 mm) for TC2030-IDC, TC2030-IDC-NL and ECV3-06-IDC. The debug lines run through series resistors; every signal is brought out individually for probing.
- from 1 pcs €30.00
- from 2 pcs €28.50
- from 3 pcs €27.00
- from 5 pcs €25.50
- from 10 pcs €24.00
Adapter board between the 20-pin ARM debug header (2 × 10, 2.54 mm) and the ten-pin IDC connector of the TC2050 cables. With series resistors, plug-in jumpers for supply and nTRST, measuring points and the pinout printed on the board.
- from 1 pcs €30.00
Adapter board from the 20-pin ARM debugger connector (2 × 10 pin, 2.54 mm) to the 14-pin 1.27 mm (0.05″) connector (1.27 mm) used by the ST-LINK V3 and by Tag-Connect's STDC14 cables. The debug lines run through series resistors; every signal is brought out individually for probing.
- from 1 pcs €30.00
Hersteller: Tag-Connect, LLC, 433 Airport Blvd, Suite 323, Burlingame, CA 94010, USA. Tel. +1 877-244-4156 · support@tag-connect.com
Verantwortliche Person in der EU (Art. 19 GPSR, da Hersteller ohne EU-Niederlassung):
Collion GmbH & Co.KG
Am Schmiedlacker 56, D-84028 Landshut
Tel. +49 (871) 2066-1000 · info@collion.de