TC-LATTICE-10 · Lattice Adapter for iCE40, SPI, TC2050

TAG-CONNECT

€40.00

From 1 pcs: €40.00 / pc

Available, delivery time: 1-3 days

Only 1 left in stock

Product number: TC-LATTICE-10

Product information "TC-LATTICE-10 · Lattice Adapter for iCE40, SPI, TC2050"

Short description

Adapter from the 12-pin connector of the Lattice HW-USBN-2B programming cable to a 10-pin 2.54 mm (0.1″) pin header for TC2050-IDC, TC2050-IDC-NL and ECV3-10-IDC cables — with DONE, PROGRAMN/ispEN, TRST and 5 V. The adapter for iCE40 and for any configuration that needs more than four JTAG lines.

Connections

Side	Pins	Connector	Pitch
Debugger	12	Socket Lattice HW-USBN-2B	—
Cable (Tag-Connect)	10	Pin header, 2 × 5	2.54 mm (0.1″)

Full pin assignment: in the "Technical data" tab.

Compatible: the Lattice HW-USBN-2B programming cable.

Not, or not directly, compatible

20-pin, 2 × 10, 2.54 mm (0.1″) — ARM connector, e.g. SEGGER J-Link, Keil ULINK, ST-LINK/V2: through the adapter board COLL-ARM20-10-IDC, TC2050-ARM2010
14-pin, 2 × 7, 2 mm — Xilinx Platform Cable II: through the adapter board TC2050-XILINX
14-pin, 2 × 7, 2.54 mm (0.1″) — Renesas E1 / E2 / E8a / E20: through the adapter board TC-RENESAS

Application

iCE40 UltraPlus, HX and LP have no JTAG. Diamond and Radiant Programmer configure them over SPI and need CRESET_B and CDONE for that — exactly the signals the 10-pin TC2050 footprint carries via ispEN/PROG and DONE. The same applies when the configuration flash on the FPGA is written directly (chip select) or when the programmer is to drive PROGRAMN.

For pure JTAG targets — ECP5, CrossLink, MachXO — the smaller TC-LATTICE with its 6-pin footprint is enough.

Which Lattice adapter?

Device	Interface	Adapter
iCE40 UltraPlus, HX, LP	SPI with CRESET_B and CDONE — no JTAG	TC-LATTICE-10
ECP5, CrossLink, MachXO2, MachXO3, ispMACH	JTAG	TC-LATTICE is enough
Writing the configuration flash on the FPGA directly	SPI with chip select	TC-LATTICE-10
PROGRAMN driven by the programmer	—	TC-LATTICE-10

In short: JTAG targets with no further demands do fine with the 6-pin; anything that needs DONE, PROGRAMN or a chip select calls for the 10-pin.

The 500 Ω resistor — and why it sits here

The HW-USBN-2B senses the target voltage via VCC. On targets with very low current draw it lifts VCC unexpectedly in doing so. Lattice therefore recommends 500 Ω between VCC and GND — on every target board. This adapter carries the resistor itself; the target board no longer needs it.

Ground first

Lattice mandates it for the HW-USBN-2B, and it holds with the adapter too: when connecting, ground first, then the signals. Otherwise the device can be damaged. The Tag-Connect contacts are all the same length — there is no mating-first ground here.

Technical data

Signals: TMS, TDI/SI, TCK/SCLK, TDO/SO, DONE, ispEN/PROG/SN, TRST, VCC, 5 V, GND
500 Ω fitted between VCC and GND
Devices: iCE40 UltraPlus/HX/LP (SPI); ECP5, CrossLink, MachXO with PROGRAMN or configuration flash

Included

The adapter only. Lattice HW-USBN-2B and cables are not included.

Bauform:	IDC-Kabelende

Pin assignment

TC2050	Signal
1	VCC*
2	TMS
3	GND*
4	TCK / SCLK
5	5 V OUT
6	TDO / SO
7	DONE
8	TDI / SI
9	TRST
10	ispEN / PROG / SN

On the back of the adapter board there is a 500 Ohm resistor between VCC and GND.

Manufacturer specification, taken from the product page at Tag-Connect. There is no PDF datasheet for this article; the manufacturer specification is binding.

Accessories

New

The ECV3-10-IDC cable in full length, with the 10-pin Edge-Connect™ connector for the board edge at one end and the 10-pin IDC connector on a 2.54 mm pitch at the other.

ECV3-10-IDC · 10-Pin Edge-Connect™ to IDC

Third-generation Edge-Connect™ connector for direct board-edge contact, terminating in a 10-pin 2.54 mm (0.1″) IDC ribbon connector. No mating connector on the target board — just one locating hole, and a low profile suited to stacked boards.

€88.00

from 1 pcs €88.00
from 20 pcs €80.96
from 30 pcs €79.20

The TC2050-IDC cable in full length, with the 10-pin Tag-Connect connector with spring pins and legs at one end and the 10-pin IDC connector on a 2.54 mm pitch at the other.

TC2050-IDC · 10-pin Debug Cable with Legs, No Connector

Ten-pin debug and programming cable with spring pins that lands straight on the board — no connector on the target, just ten contact pads and six holes. The four legs hold it there while you work. At the other end, a standard 2.54 mm (0.1″) ribbon header that fits nearly every debugger.

€40.00

from 1 pcs €40.00
from 20 pcs €36.80
from 30 pcs €36.00

The TC2050-IDC-NL cable in full length, with the 10-pin Tag-Connect connector with spring pins, no legs at one end and the 10-pin IDC connector on a 2.54 mm pitch at the other.

TC2050-IDC-NL · 10-pin Cable, No Legs, Smallest Footprint

Ten-pin debug and programming cable with spring pins, without legs — the smallest debug access a board can have: ten contact pads and three holes, nothing else. At the other end a standard 2.54 mm (0.1″) ribbon header.

€38.00

from 1 pcs €38.00
from 3 pcs €37.00
from 5 pcs €36.00