TC2050-XILINX · Adapter for Xilinx Platform Cable
€40.00
- From 1 pcs: €40.00 / pc
Available, delivery time: 1-3 days
Only 1 left in stock
Product information "TC2050-XILINX · Adapter for Xilinx Platform Cable"
Short description
Adapter for the 2mm 14-pin header found on Xilinx's Platform Cable II and compatible programmers — to a 10-pin 2.54 mm (0.1″) header for TC2050-IDC Plug-of-Nails™ cables.
Connections
| Side | Pins | Connector | Pitch |
|---|---|---|---|
| Debugger | 14 | Socket Xilinx Platform Cable II, 2 × 7 | 2 mm |
| Cable (Tag-Connect) | 10 | Pin header, 2 × 5 | 2.54 mm (0.1″) |
Full pin assignment: in the "Technical data" tab.
Compatible: Xilinx Platform Cable II and compatible programmers.
Not, or not directly, compatible
- 14-pin, 2 × 7, 2.54 mm (0.1″) — Renesas E1 / E2 / E8a / E20: through the adapter board TC-RENESAS
- 20-pin, 2 × 10, 2.54 mm (0.1″) — ARM connector, e.g. SEGGER J-Link, Keil ULINK, ST-LINK/V2: through the adapter board COLL-ARM20-10-IDC, TC2050-ARM2010
- 12-pin — Lattice HW-USBN-2B: through the adapter board TC-LATTICE-10
Easily confused: The pitch is 2 mm, not 2.54 mm.
Technical data
- Also works with standard 10-pin 2.54 mm (0.1″) ribbon headers on the target board
In use with these devices
Xilinx Platform Cable (Xilinx, JTAG)
What counts is the connector, not the device name: compare the connector on your device with the table above. If it carries a different one, the route goes through an adapter board.
Included
Adapter only. Not included: cable.
Variants
TC2050-XILINX-M — for Digilent JTAG-HS2/HS3 (female 14-pin 2mm connector). TC-XILINX6 — for 6-pin TC2030-IDC cables.
| Bauform: | IDC-Kabelende |
|---|
Manufacturer's datasheet (PDF, copy hosted by us)
Pin assignment
| Xilinx Platform Cable | Signal | TC2050 |
|---|---|---|
| 2 | VREF | 1 |
| 4 | TMS / SS / PROG | 2 |
| 6 | TCK / SCLK / CCLK | 4 |
| 8 | TDO / MISO / DONE | 6 |
| 10 | TDI / MOSI / DIN | 8 |
| 13 | PGND | 9 |
| 14 | HALT / WP / INIT | 10 |
| 3, 5, 7, 9, 11 | GND | 3, 5, 7 |
Not connected: 1, 12 (NC).
Xilinx recommends a ribbon cable of about 150 mm (6") for the Platform Cable II. For signal integrity it can make sense to keep the TC2050-IDC cable correspondingly short.
From the manufacturer datasheet (TC2050-XILINX.pdf).
Accessories
Third-generation Edge-Connect™ connector for direct board-edge contact, terminating in a 10-pin 2.54 mm (0.1″) IDC ribbon connector. No mating connector on the target board — just one locating hole, and a low profile suited to stacked boards.
- from 1 pcs €88.00
- from 20 pcs €80.96
- from 30 pcs €79.20
Ten-pin debug and programming cable with spring pins that lands straight on the board — no connector on the target, just ten contact pads and six holes. The four legs hold it there while you work. At the other end, a standard 2.54 mm (0.1″) ribbon header that fits nearly every debugger.
- from 1 pcs €40.00
- from 20 pcs €36.80
- from 30 pcs €36.00
Ten-pin debug and programming cable with spring pins, without legs — the smallest debug access a board can have: ten contact pads and three holes, nothing else. At the other end a standard 2.54 mm (0.1″) ribbon header.
- from 1 pcs €38.00
- from 3 pcs €37.00
- from 5 pcs €36.00
Related products
JTAG adapter from the 12-pin connector of the Lattice HW-USBN-2B programming cable to a 6-pin 2.54 mm (0.1″) pin header for TC2030-IDC, TC2030-IDC-NL and ECV3-06-IDC cables — for ECP5, CrossLink, MachXO2/MachXO3 and ispMACH. The smallest Tag-Connect footprint for Lattice devices with JTAG.
- from 1 pcs €40.00
Adapter from the 12-pin connector of the Lattice HW-USBN-2B programming cable to a 10-pin 2.54 mm (0.1″) pin header for TC2050-IDC, TC2050-IDC-NL and ECV3-10-IDC cables — with DONE, PROGRAMN/ispEN, TRST and 5 V. The adapter for iCE40 and for any configuration that needs more than four JTAG lines.
- from 1 pcs €40.00
Hersteller: Tag-Connect, LLC, 433 Airport Blvd, Suite 323, Burlingame, CA 94010, USA. Tel. +1 877-244-4156 · support@tag-connect.com
Verantwortliche Person in der EU (Art. 19 GPSR, da Hersteller ohne EU-Niederlassung):
Collion GmbH & Co.KG
Am Schmiedlacker 56, D-84028 Landshut
Tel. +49 (871) 2066-1000 · info@collion.de