ECV3-10-IDC · 10-Pin Edge-Connect™ to IDC
€88.00
- From 1 pcs: €88.00 / pc
- From 20 pcs: €80.96 / pc
- From 30 pcs: €79.20 / pc
Available, delivery time: 1-3 days
Only 5 left in stock
Product information "ECV3-10-IDC · 10-Pin Edge-Connect™ to IDC"
Short description
Third-generation Edge-Connect™ connector for direct board-edge contact, terminating in a 10-pin 2.54 mm (0.1″) IDC ribbon connector. No mating connector on the target board — just one locating hole, and a low profile suited to stacked boards.
Connections
| Side | Pins | Connector | Pitch |
|---|---|---|---|
| Board (Tag-Connect) | 10 | Edge contacts ECV3-10 (Edge-Connect™) | 1.27 mm (0.05″) |
| Debugger | 10 | Socket, 2 × 5 | 2.54 mm (0.1″) |
Pin assignment: contact n is on connector pin n, the cable is wired 1:1 — the full table is in the "Technical data" tab.
Compatible: programmers with a 10-pin 2.54 mm pin header — among them PEmicro Multilink and Cyclone, and the Intel/Altera USB-Blaster.
Not, or not directly, compatible
- 10-pin, 2 × 5, 1.27 mm (0.05″) — Cortex connector, e.g. Keil ULINK2: ECV3-10-IDC-050
- 20-pin, 2 × 10, 2.54 mm (0.1″) — ARM connector, e.g. SEGGER J-Link, Keil ULINK, ST-LINK/V2: through the adapter board COLL-ARM20-10-IDC, TC2050-ARM2010
- 12-pin — Lattice HW-USBN-2B: through the adapter board TC-LATTICE-10
- 14-pin, 2 × 7, 1.27 mm (0.05″) — STDC14, e.g. ST-LINK V3: ECV3-10-IDC-STDC14
- 14-pin, 2 × 7, 2 mm — Xilinx Platform Cable II: through the adapter board TC2050-XILINX
- 14-pin, 2 × 7, 2.54 mm (0.1″) — Renesas E1 / E2 / E8a / E20: through the adapter board TC-RENESAS
- 20-pin, 2 × 10, 1.27 mm (0.05″) — e.g. Keil ULINK2: ECV3-10-IDC-050-20
Technical data
- Target board requires: one non-plated locating hole
In use with these devices
Lattice HW-USBN-2B (JTAG, SPI/PDI) · ST-LINK/V2 and V3 SET (JTAG, SWD) · PEmicro Multilink/Cyclone series (JTAG, SWD) · Segger J-LINK (JTAG, SWD) · Intel/Altera USB/Byte Blaster (JTAG) · Xilinx Platform Cable (JTAG) · TI XDS100v2 (JTAG)
What counts is the connector, not the device name: compare the connector on your device with the table above. If it carries a different one, the route goes through an adapter board.
Included
Ribbon cable and IDC connector. Not included: demo PCB.
Variants
ECV3-06-IDC — 6-pin version. ECV3-10-IDC-050 — 10-pin to 1.27 mm (0.05″) IDC.
| Form Factor: | ECV3 Edge Connector, IDC-Kabelende |
|---|
Manufacturer's datasheet (PDF, copy hosted by us)
Pin assignment
| IDC | ECV3-10 |
|---|---|
| 1 | 1 |
| 2 | 2 |
| 3 | 3 |
| 4 | 4 |
| 5 | 5 |
| 6 | 6 |
| 7 | 7 |
| 8 | 8 |
| 9 | 9 |
| 10 | 10 |
The cable is wired 1:1: edge contact n sits on connector pin n.
Confirmed by us.
Accessories
A small board carrying the Edge-Connect™ footprints at full size — to handle, measure and try out before you commit the pattern to your own layout. The V3 denotes the third generation of the Edge-Connect series — the same one the ECV3 cables belong to.
- from 1 pcs €2.00
Adapter that makes TC2050-IDC cables usable for ARM JTAG and ARM SWD applications — converts the 20-pin ARM connector (2.54 mm / 0.1″) to a 10-pin header on the same pitch.
- from 1 pcs €30.00
Adapter board between the 20-pin ARM debug header (2 × 10, 2.54 mm) and the ten-pin IDC connector of the TC2050 Plug-of-Nails™ cables. With series resistors, plug-in jumpers for supply and nTRST, measuring points and the pinout printed on the board.
- from 1 pcs €25.00
- from 3 pcs €24.00
- from 5 pcs €23.00
Adapter from the 12-pin connector of the Lattice HW-USBN-2B programming cable to a 10-pin 2.54 mm (0.1″) pin header for TC2050-IDC, TC2050-IDC-NL and ECV3-10-IDC cables — with DONE, PROGRAMN/ispEN, TRST and 5 V. The adapter for iCE40 and for any configuration that needs more than four JTAG lines.
- from 1 pcs €40.00
Adapter for the 2mm 14-pin header found on Xilinx's Platform Cable II and compatible programmers — to a 10-pin 2.54 mm (0.1″) header for TC2050-IDC Plug-of-Nails™ cables.
- from 1 pcs €40.00
Storage case for Tag-Connect cables and accessories — the same one as in the TC2050 evaluation kit. Grey plastic case with carrying handle, a foam insert with compartments inside and convoluted foam in the lid. Room for one or two cables together with accessories such as an adapter, clip or grip.
- from 1 pcs €19.00
Related products
Edge-Connect™ board-edge connector, terminating in a 10-pin 1.27 mm (0.05″) IDC ribbon connector. Fits debuggers with Samtec FTSH-105-01 style micro-headers (e.g. ULINK2).
- from 1 pcs €88.00
Edge-Connect™ cable with a 10-pin ECV3 board-edge connector, terminating in a 20-pin 1.27 mm (0.05″) ribbon connector. Fits ULINK2 and similar debuggers using Samtec FTSH-110-01 style micro-headers.
- from 1 pcs €88.00
Edge-Connect™ cable with ten contacts at the board edge, terminating in the
- from 1 pcs €88.00
Ten-pin debug and programming cable with spring pins that lands straight on the board — no connector on the target, just ten contact pads and six holes. The four legs hold it there while you work. At the other end, a standard 2.54 mm (0.1″) ribbon header that fits nearly every debugger.
- from 1 pcs €40.00
- from 20 pcs €36.80
- from 30 pcs €36.00
Ten-pin debug and programming cable with spring pins, without legs — the smallest debug access a board can have: ten contact pads and three holes, nothing else. At the other end a standard 2.54 mm (0.1″) ribbon header.
- from 1 pcs €38.00
- from 3 pcs €37.00
- from 5 pcs €36.00
Adapter board between the 20-pin ARM debug header (2 × 10, 2.54 mm) and the ten-pin IDC connector of the TC2050 Plug-of-Nails™ cables. With series resistors, plug-in jumpers for supply and nTRST, measuring points and the pinout printed on the board.
- from 1 pcs €25.00
- from 3 pcs €24.00
- from 5 pcs €23.00
Hersteller: Tag-Connect, LLC, 433 Airport Blvd, Suite 323, Burlingame, CA 94010, USA. Tel. +1 877-244-4156 · support@tag-connect.com
Verantwortliche Person in der EU (Art. 19 GPSR, da Hersteller ohne EU-Niederlassung):
Collion GmbH & Co.KG
Am Schmiedlacker 56, D-84028 Landshut
Tel. +49 (871) 2066-1000 · info@collion.de