JTAG - SoC / FPGA
Edge-Connect™ connector for direct board-edge contact — no mating connector on the target board, just one locating hole. Terminates in a 6-pin 2.54 mm (0.1″) IDC ribbon connector.
- from 1 pcs €85.00
Third-generation Edge-Connect™ connector for direct board-edge contact, terminating in a 10-pin 2.54 mm (0.1″) IDC ribbon connector. No mating connector on the target board — just one locating hole, and a low profile suited to stacked boards.
- from 1 pcs €88.00
- from 20 pcs €80.96
- from 30 pcs €79.20
14-pin Edge-Connect™ with two guide pins, terminating in a **2 mm IDC header** — the pitch between 1.27 mm (0.05″) and 2.54 mm (0.1″).
- from 1 pcs €92.00
JTAG adapter from the 12-pin connector of the Lattice HW-USBN-2B programming cable to a 6-pin 2.54 mm (0.1″) pin header for TC2030-IDC, TC2030-IDC-NL and ECV3-06-IDC cables — for ECP5, CrossLink, MachXO2/MachXO3 and ispMACH. The smallest Tag-Connect footprint for Lattice devices with JTAG.
- from 1 pcs €40.00
Adapter from the 12-pin connector of the Lattice HW-USBN-2B programming cable to a 10-pin 2.54 mm (0.1″) pin header for TC2050-IDC, TC2050-IDC-NL and ECV3-10-IDC cables — with DONE, PROGRAMN/ispEN, TRST and 5 V. The adapter for iCE40 and for any configuration that needs more than four JTAG lines.
- from 1 pcs €40.00
Connects a 6-pin Plug-of-Nails™ target (legged) to a 10-pin 2.54 mm (0.1″) IDC socket, for select Altera USB Blaster/ByteBlaster programmers.
- from 1 pcs €65.00
Connects a 6-pin Plug-of-Nails™ target (no legs) to a 10-pin 2.54 mm (0.1″) IDC socket, for select Altera USB Blaster/ByteBlaster programmers.
- from 1 pcs €65.00
6-pin Plug-of-Nails™ cable, legged, with a 6-pin 2.54 mm (0.1″) ribbon connector to the host. Snaps directly into a tiny PCB footprint — no mating connector needed on the target board.
- from 1 pcs €35.00
- from 20 pcs €32.20
- from 30 pcs €31.50
Like TC2030-IDC — six contacts on the board, 6-pin 2.54 mm (0.1″) connector at the debugger — but 254 mm (10″) instead of the standard length — for extra distance between debugger and target board.
- from 1 pcs €35.00
- from 20 pcs €32.20
- from 30 pcs €31.50
6-pin Plug-of-Nails™ cable, no legs, with a 6-pin 2.54 mm (0.1″) ribbon connector. Footprint about the size of an 0805 SMT resistor.
- from 1 pcs €35.00
- from 20 pcs €32.20
- from 30 pcs €31.50
Like TC2030-IDC-NL — six contacts on the board, 6-pin 2.54 mm (0.1″) connector at the debugger — but 254 mm (10″) instead of the standard length.
- from 1 pcs €35.00
Ten-pin debug and programming cable with spring pins that lands straight on the board — no connector on the target, just ten contact pads and six holes. The four legs hold it there while you work. At the other end, a standard 2.54 mm (0.1″) ribbon header that fits nearly every debugger.
- from 1 pcs €40.00
- from 20 pcs €36.80
- from 30 pcs €36.00
Ten-pin debug and programming cable with spring pins, without legs — the smallest debug access a board can have: ten contact pads and three holes, nothing else. At the other end a standard 2.54 mm (0.1″) ribbon header.
- from 1 pcs €38.00
- from 3 pcs €37.00
- from 5 pcs €36.00
Adapter for the 2mm 14-pin header found on Xilinx's Platform Cable II and compatible programmers — to a 10-pin 2.54 mm (0.1″) header for TC2050-IDC Plug-of-Nails™ cables.
- from 1 pcs €40.00