ECV3-14-2AP-IDC · 14-pin Edge-Connect to 2.54 mm (0.1″) IDC
€92.00
- From 1 pcs: €92.00 / pc
Available, delivery time: 1-3 days
Only 3 left in stock
Product information "ECV3-14-2AP-IDC · 14-pin Edge-Connect to 2.54 mm (0.1″) IDC"
Short description
14-pin Edge-Connect™ with two guide pins, terminating in a 2.54 mm (0.1″) IDC header — the classic ribbon connector on a 2.54 mm pitch.
Connections
| Side | Pins | Connector | Pitch |
|---|---|---|---|
| Board (Tag-Connect) | 14 | Edge contacts ECV3-14 (Edge-Connect™), two alignment pins | 1.27 mm (0.05″) |
| Debugger | 14 | Socket, 2 × 7 | 2.54 mm (0.1″) |
Pin assignment: contact n is on connector pin n, the cable is wired 1:1 — the full table is in the "Technical data" tab.
Compatible: debuggers with a 14-pin 2.54 mm pin header.
Not, or not directly, compatible
- 14-pin, 2 × 7, 1.27 mm (0.05″): ECV3-14-2AP-IDC-050
- 14-pin, 2 × 7, 2 mm: ECV3-14-2AP-IDC-2MM
- 20-pin, 2 × 10, 1.27 mm (0.05″) — Cortex with trace, e.g. Keil ULINK Pro: ECV3-14-2AP-ETM
What you need it for
Edge-Connect places the contacts on the edge of the board rather than on its surface. The target board needs no mating connector at all — just the plated half-holes along the edge and the holes for the guide pins. That saves space and the cost of a component on every board you build.
What "2AP" means
Two guide pins instead of one. The connector cannot be seated askew and stays reproducible over repeated cycles. Tag-Connect recommends this version for all new designs using the 14-pin Edge-Connect.
Compatibility, important
ECV3 is the third generation and is not compatible with the earlier Edge-Connect families. If you are working with an older board, you need the older cable — both remain available.
Included
Cable with Edge-Connect™ connector and IDC header. The demo PCB shown in the manufacturer's photos is not included.
The family at a glance
All four versions share the same board side. What differs is only the header at the debugger:
| Article | Debugger side |
|---|---|
| ECV3-14-2AP-IDC | 14-pin, 2.54 mm (0.1″) |
| ECV3-14-2AP-IDC-050 | 14-pin, 1.27 mm (0.05″) |
| ECV3-14-2AP-IDC-2MM | 14-pin, 2 mm |
| ECV3-14-2AP-ETM | 20-pin Cortex-20, with trace |
So it is your debugger that decides, not your board. If in doubt, measure the pin spacing on your programmer.
On connector numbering: Why the six-pin Tag-Connect counts differently
| Form Factor: | ECV3 Edge Connector, IDC-Kabelende |
|---|
Datasheet with our advisory note (PDF — manufacturer's drawing with a note from us in front)
Pin assignment
| IDC | ECV3-14 |
|---|---|
| 1 | 1 |
| 2 | 2 |
| 3 | 3 |
| 4 | 4 |
| 5 | 5 |
| 6 | 6 |
| 7 | 7 |
| 8 | 8 |
| 9 | 9 |
| 10 | 10 |
| 11 | 11 |
| 12 | 12 |
| 13 | 13 |
| 14 | 14 |
The cable is wired 1:1: edge contact n sits on connector pin n.
Confirmed by us.
Accessories
A small board carrying the Edge-Connect™ footprints at full size — to handle, measure and try out before you commit the pattern to your own layout. The V3 denotes the third generation of the Edge-Connect series — the same one the ECV3 cables belong to.
- from 1 pcs €2.00
Storage case for Tag-Connect cables and accessories — the same one as in the TC2050 evaluation kit. Grey plastic case with carrying handle, a foam insert with compartments inside and convoluted foam in the lid. Room for one or two cables together with accessories such as an adapter, clip or grip.
- from 1 pcs €19.00
Related products
14-pin Edge-Connect™ with two guide pins, terminating in a **1.27 mm (0.05″) IDC header** — the narrow ribbon connector on a 1.27 mm pitch.
- from 1 pcs €92.00
14-pin Edge-Connect™ with two guide pins, terminating in a **2 mm IDC header** — the pitch between 1.27 mm (0.05″) and 2.54 mm (0.1″).
- from 1 pcs €92.00
14-pin Edge-Connect™ with two guide pins, terminating in the **20-pin Cortex-20 header on 1.27 mm (0.05″)** and carrying the trace signals.
- from 1 pcs €92.00
14-pin Plug-of-Nails™ cable, legged, terminating in a 14-pin (2×7) 2.54 mm (0.1″) ribbon connector.
- from 1 pcs €65.00
14-pin Plug-of-Nails™ cable, no legs, terminating in a 2.54 mm (0.1″) IDC ribbon connector (2×7 pin).
- from 1 pcs €65.00
10-contact legged programming cable for TI's MSP-FET430 debugger and its 14-pin 2.54 mm (0.1″) connector, compatible with all MSP430 microcontrollers — direct contact with no mating connector needed on the target board.
- from 1 pcs €50.00
10-contact spring-pin cable, no Legs, for TI's MSP-FET430 debugger and its 14-pin 2.54 mm (0.1″) connector, compatible with all MSP430 microcontrollers.
- from 1 pcs €50.00
Hersteller: Tag-Connect, LLC, 433 Airport Blvd, Suite 323, Burlingame, CA 94010, USA. Tel. +1 877-244-4156 · support@tag-connect.com
Verantwortliche Person in der EU (Art. 19 GPSR, da Hersteller ohne EU-Niederlassung):
Collion GmbH & Co.KG
Am Schmiedlacker 56, D-84028 Landshut
Tel. +49 (871) 2066-1000 · info@collion.de