TC2030-CTX-NL-STDC14 · Cable for STLINK-V3
€42.00
- From 1 pcs: €42.00 / pc
Available, delivery time: 1-3 days
More than 5 in stock
Product information "TC2030-CTX-NL-STDC14 · Cable for STLINK-V3"
Short description
6-pin TC2030-NL cable, no legs, for STM32 targets with STLINK-V3/STLINK-V3MINI. 14-pin ribbon connector on 1.27 mm (0.05″) in STDC14 (FTSH-107) format, carries SWD including the SWO signal.
Connections
| Side | Pins | Connector | Pitch |
|---|---|---|---|
| Board (Tag-Connect) | 6 | Footprint TC2030, no Legs | 1.27 mm (0.05″) |
| Debugger | 14 | Socket STDC14 (FTSH-107 style), 2 × 7 | 1.27 mm (0.05″) |
Pin assignment: TC2030 1–6 to STDC14 3, 4, 6, 8, 12, with GND on 5 and 7 — the full table is in the "Technical data" tab.
Compatible: ST-LINK V3, V3MINI and V3SET, and other debuggers with a 14-pin 1.27 mm connector (STDC14, FTSH-107 style).
Not, or not directly, compatible
- 20-pin, 2 × 10, 2.54 mm (0.1″) — ARM connector, e.g. SEGGER J-Link, Keil ULINK, ST-LINK/V2: through the adapter board COLL-ARM20-14P-050
- 10-pin, 2 × 5, 1.27 mm (0.05″) — Cortex connector, e.g. Keil ULINK2: TC2030-CTX-NL
- 10-pin, 2 × 5, 2.54 mm (0.1″) — e.g. PEmicro Multilink, USB-Blaster: TC2030-ALT-NL
- 20-pin, 2 × 10, 1.27 mm (0.05″) — Cortex with trace, e.g. Keil ULINK Pro: TC2030-CTX-20-NL
- 6-pin, 2 × 3, 2.54 mm (0.1″): TC2030-IDC-NL
- 6-pin, single row, 2.54 mm (0.1″) — Microchip PICkit 3/4/5: TC2030-PKT-NL
- RJ12 socket (6P6C) — Microchip ICD 3, ICD 4, PICkit 3, PM3: TC2030-MCP-NL
Easily confused: The ST-LINK/V2 and the older ST-LINKs carry a 20-pin 2.54 mm connector, not this one.
Technical data
- Version: 6-pin Tag-Connect, no legs
- Protocol: SWD incl. SWO
- Former part number: TC2030-CTX-NL-ST14
In use with these devices
STLINK-V3SET (ST STM32, SWD) · STLINK-V3 (ST STM32, SWD) · STLINK-V3MINI (ST STM32, SWD)
What counts is the connector, not the device name: compare the connector on your device with the table above. If it carries a different one, the route goes through an adapter board.
Variants
TC2030-CTX-STDC14 — legged version. TC2070-IDC-NL-050 — alternative with all 14 pins connected.
| Bauform: | NL (No Legs) |
|---|
Manufacturer's datasheet (PDF, copy hosted by us)
Pin assignment
| STDC14 | Signal | TC2030 |
|---|---|---|
| 3 | T_VCC | 1 |
| 4 | T_SWDIO | 2 |
| 5 | GND | 5 |
| 6 | T_SWCLK | 4 |
| 7 | GND | 5 |
| 8 | T_SWO | 6 |
| 12 | T_NRST | 3 |
Not connected: 1, 2 (reserved by ST), 9 (T_JRCLK), 10 (T_JTDI), 11 (GNDDETECT), 13, 14 (Virtual COM Port).
Two counts that are easily confused: the ribbon at the STDC14 connector has ten conductors and contacts pins 3 to 12 there. Six of those signals reach the six-contact footprint, seven with the bridge for GNDDetect. The remaining conductors end at the connector.
Pin assignment as specified by the manufacturer.
Accessories
Protective cap for the 6-pin TC2030 cable family (Plug-of-Nails™). Protects spring contacts, steel guide pins and — where present — retention tabs during storage and transport.
- from 1 pcs €5.00
Temporarily holds a TC2030-NL cable in place on the target board — for hands-free debugging where board space is tight. 3-pack.
- from 1 pcs €22.00
- from 20 pcs €20.24
- from 30 pcs €19.80
Holds a TC2030-NL cable permanently against the target board — 3-pack.
- from 1 pcs €14.00
- from 20 pcs €12.88
- from 30 pcs €12.60
Demo board carrying every Tag-Connect footprint size, for comparison before laying out your own board — 6-, 10- and 14-pin, each with and without legs, plus the EC-10 Edge-Connect™ footprint.
- from 1 pcs €2.00
Adapter board from the 20-pin ARM debugger connector (2 × 10 pin, 2.54 mm) to the 14-pin 1.27 mm (0.05″) connector (1.27 mm) used by the ST-LINK V3 and by Tag-Connect's STDC14 cables (Plug-of-Nails™). The debug lines run through series resistors; every signal is brought out individually for probing.
- from 1 pcs €25.00
- from 3 pcs €24.00
- from 5 pcs €23.00
Related products
6-pin TC2030 Plug-of-Nails™ cable, legged, for ARM Cortex targets. 10-pin ribbon connector on 1.27 mm (0.05″) in FTSH-105 format (Cortex Debug standard, e.g. Keil ULINK2).
- from 1 pcs €45.00
6-pin TC2030-NL Plug-of-Nails™ programming cable, no legs, for ARM Cortex targets. 10-pin ribbon connector on 1.27 mm (0.05″) in FTSH-105 format, saves over 66% board area versus classic FTSH-105 micro-headers.
- from 1 pcs €45.00
6-pin TC2030-NL Plug-of-Nails™ cable, no legs, for ARM Cortex targets — with the 10-pin 1.27 mm (0.05″) ribbon connector fitted reversed at the factory, specifically for Atmel-ICE.
- from 1 pcs €50.00
6-pin TC2030 cable with legs and a 20-pin 1.27 mm connector — for debuggers with the ARM Cortex Debug+ETM port: IAR I-Jet, Keil ULINK Pro, SEGGER J-Trace. Electrically identical to the TC2030-CTX; only the debugger-side connector differs.
- from 1 pcs €55.00
6-pin TC2030 cable without legs and with a 20-pin 1.27 mm connector for IAR I-Jet, Keil ULINK Pro and SEGGER J-Trace. For boards that should not get leg holes, and for connections that last longer than one programming cycle.
- from 1 pcs €55.00
6-pin TC2030 cable, legged, for STM32 targets with STLINK-V3/STLINK-V3MINI. 14-pin ribbon connector on 1.27 mm (0.05″) in STDC14 (FTSH-107) format, carries SWD including the SWO signal.
- from 1 pcs €42.00
10-pin Plug-of-Nails™ cable, no legs, with a 14-pin 1.27 mm (0.05″) ribbon connector in STDC14 format for STLINK-V3/STLINK-V3MINI.
- from 1 pcs €66.00
Edge-Connect™ cable with six contacts at the board edge, terminating in the
- from 1 pcs €85.00
Hersteller: Tag-Connect, LLC, 433 Airport Blvd, Suite 323, Burlingame, CA 94010, USA. Tel. +1 877-244-4156 · support@tag-connect.com
Verantwortliche Person in der EU (Art. 19 GPSR, da Hersteller ohne EU-Niederlassung):
Collion GmbH & Co.KG
Am Schmiedlacker 56, D-84028 Landshut
Tel. +49 (871) 2066-1000 · info@collion.de