TC2030-MCP-NL · RJ12 Cable for Microchip ICD
€50.00
- From 1 pcs: €50.00 / pc
Available in 7 days, delivery time 1-3 days
Product information "TC2030-MCP-NL · RJ12 Cable for Microchip ICD"
Short description
Connects a 6-pin Plug-of-Nails™ target (no legs) via an RJ12 modular connector to a Microchip ICD programmer. Footprint barely bigger than an SMT resistor.
Connections
| Side | Pins | Connector | Pitch |
|---|---|---|---|
| Board (Tag-Connect) | 6 | Footprint TC2030, no Legs | 1.27 mm (0.05″) |
| Debugger | 6 | Modular plug RJ12 (6P6C) | — |
Pin assignment: mirrored — contact 1 on pin 6, contact 6 on pin 1 — the full table is in the "Technical data" tab. Assignment measured by us — not yet documented by the manufacturer.
Compatible: Microchip programmers with an RJ12 socket — ICD 3, ICD 4, PICkit 3, PM3.
Not, or not directly, compatible
- 6-pin, 2 × 3, 2.54 mm (0.1″): TC2030-IDC-NL
- 6-pin, single row, 2.54 mm (0.1″) — Microchip PICkit 3/4/5: TC2030-PKT-NL
- 10-pin, 2 × 5, 1.27 mm (0.05″) — Cortex connector, e.g. Keil ULINK2: TC2030-CTX-NL
- 10-pin, 2 × 5, 2.54 mm (0.1″) — e.g. PEmicro Multilink, USB-Blaster: TC2030-ALT-NL
- 14-pin, 2 × 7, 1.27 mm (0.05″) — STDC14, e.g. ST-LINK V3: TC2030-CTX-NL-STDC14
- 20-pin, 2 × 10, 1.27 mm (0.05″) — Cortex with trace, e.g. Keil ULINK Pro: TC2030-CTX-20-NL
Easily confused: Check your device for a telephone-style socket.
Application
Primarily intended for production programming with brief contact time. Compatible with the TC2030-MCP footprint — develop with the legged variant, produce with this no-legs variant. For a permanent connection, use TC2030-MCP. For debugging, combine with the TC2030-CLIP clip.
In use with these devices
Microchip ICD4 · Microchip ICD 3 · Microchip PM3 · Microchip PICkit 3 · CCS Programmers · Targets: Microchip PIC, PIC32, dsPIC
What counts is the connector, not the device name: compare the connector on your device with the table above. If it carries a different one, the route goes through an adapter board.
| Bauform: | NL (No Legs) |
|---|
Pin assignment
| RJ12 | Signal | TC2030 |
|---|---|---|
| 1 | NC / LVP | 6 |
| 2 | PGC (ICSPCLK) | 5 |
| 3 | PGD (ICSPDAT) | 4 |
| 4 | GND | 3 |
| 5 | VDD | 2 |
| 6 | MCLR / VPP | 1 |
The order is mirrored: contact 1 of the footprint sits on pin 6 of the modular plug. The signals are Microchip ICSP — if you know the TC2030 footprint from the ARM world, note the difference: ground is on contact 3, not contact 5.
Assignment measured by us — not yet documented by the manufacturer. The measurement was taken on the TC2030-MCP; this article has the same cable internals.
Accessories
Protective cap for the 6-pin TC2030 cable family (Plug-of-Nails™). Protects spring contacts, steel guide pins and — where present — retention tabs during storage and transport.
- from 1 pcs €5.00
Temporarily holds a TC2030-NL cable in place on the target board — for hands-free debugging where board space is tight. 3-pack.
- from 1 pcs €22.00
- from 20 pcs €20.24
- from 30 pcs €19.80
Holds a TC2030-NL cable permanently against the target board — 3-pack.
- from 1 pcs €14.00
- from 20 pcs €12.88
- from 30 pcs €12.60
Demo board carrying every Tag-Connect footprint size, for comparison before laying out your own board — 6-, 10- and 14-pin, each with and without legs, plus the EC-10 Edge-Connect™ footprint.
- from 1 pcs €2.00
Related products
Connects a 6-pin Plug-of-Nails™ target (legged) via an RJ12 modular connector to a Microchip ICD programmer.
- from 1 pcs €50.00
Like TC2030-MCP — six contacts on the board, RJ12 modular plug at the programmer — but 254 mm (10″) instead of the standard length.
- from 1 pcs €50.00
- from 20 pcs €46.00
- from 30 pcs €45.00
Like TC2030-MCP-NL — six contacts on the board, RJ12 modular plug at the programmer — but 254 mm (10″) instead of the standard length.
- from 1 pcs €50.00
Connects a 6-pin Plug-of-Nails™ target (legged) to Microchip's PICkit 3/4/5, via a 6-pin 2.54 mm (0.1″) SIP header.
- from 1 pcs €48.00
Connects a 6-pin Plug-of-Nails™ target (no legs) to Microchip's PICkit 3/4/5 — through a single-row 6-pin header on 2.54 mm (0.1″). Footprint barely bigger than an SMT resistor.
- from 1 pcs €48.00
Hersteller: Tag-Connect, LLC, 433 Airport Blvd, Suite 323, Burlingame, CA 94010, USA. Tel. +1 877-244-4156 · support@tag-connect.com
Verantwortliche Person in der EU (Art. 19 GPSR, da Hersteller ohne EU-Niederlassung):
Collion GmbH & Co.KG
Am Schmiedlacker 56, D-84028 Landshut
Tel. +49 (871) 2066-1000 · info@collion.de