TC2030-MCP-NL-10 · RJ12 Cable, No Legs, 254 mm (10″)
€50.00
- From 1 pcs: €50.00 / pc
Available in 7 days, delivery time 1-3 days
Product information "TC2030-MCP-NL-10 · RJ12 Cable, No Legs, 254 mm (10″)"
Short description
Like TC2030-MCP-NL — six contacts on the board, RJ12 modular plug at the programmer — but 254 mm (10″) instead of the standard length.
Connections
| Side | Pins | Connector | Pitch |
|---|---|---|---|
| Board (Tag-Connect) | 6 | Footprint TC2030, no Legs | 1.27 mm (0.05″) |
| Debugger | 6 | Modular plug RJ12 (6P6C) | — |
Pin assignment: mirrored — contact 1 on pin 6, contact 6 on pin 1 — the full table is in the "Technical data" tab. Assignment measured by us — not yet documented by the manufacturer.
Compatible: Microchip programmers with an RJ12 socket — ICD 3, ICD 4, PICkit 3, PM3.
Not, or not directly, compatible
- 6-pin, 2 × 3, 2.54 mm (0.1″): TC2030-IDC-NL
- 6-pin, single row, 2.54 mm (0.1″) — Microchip PICkit 3/4/5: TC2030-PKT-NL
- 10-pin, 2 × 5, 1.27 mm (0.05″) — Cortex connector, e.g. Keil ULINK2: TC2030-CTX-NL
- 10-pin, 2 × 5, 2.54 mm (0.1″) — e.g. PEmicro Multilink, USB-Blaster: TC2030-ALT-NL
- 14-pin, 2 × 7, 1.27 mm (0.05″) — STDC14, e.g. ST-LINK V3: TC2030-CTX-NL-STDC14
- 20-pin, 2 × 10, 1.27 mm (0.05″) — Cortex with trace, e.g. Keil ULINK Pro: TC2030-CTX-20-NL
Easily confused: Check your device for a telephone-style socket.
Important note
254 mm (10″) exceeds Microchip's specified maximum cable length of approx. 200 mm (8″) — officially not supported by Microchip, though per Tag-Connect it hasn't caused known problems in practice. The small TC2030 footprint usually allows the ICD connection to be placed right at the MCU rather than routing long traces out to the connector.
In use with these devices
Microchip ICD4 · Microchip ICD 3 · CCS Programmers · Targets: Microchip PIC, PIC32, dsPIC (PIC ICD/ICSP)
What counts is the connector, not the device name: compare the connector on your device with the table above. If it carries a different one, the route goes through an adapter board.
| Bauform: | NL (No Legs) |
|---|
Pin assignment
| RJ12 | Signal | TC2030 |
|---|---|---|
| 1 | NC / LVP | 6 |
| 2 | PGC (ICSPCLK) | 5 |
| 3 | PGD (ICSPDAT) | 4 |
| 4 | GND | 3 |
| 5 | VDD | 2 |
| 6 | MCLR / VPP | 1 |
The order is mirrored: contact 1 of the footprint sits on pin 6 of the modular plug. The signals are Microchip ICSP — if you know the TC2030 footprint from the ARM world, note the difference: ground is on contact 3, not contact 5.
Assignment measured by us — not yet documented by the manufacturer. The measurement was taken on the TC2030-MCP; this article has the same cable internals.
Accessories
Protective cap for the 6-pin TC2030 cable family (Plug-of-Nails™). Protects spring contacts, steel guide pins and — where present — retention tabs during storage and transport.
- from 1 pcs €5.00
Temporarily holds a TC2030-NL cable in place on the target board — for hands-free debugging where board space is tight. 3-pack.
- from 1 pcs €22.00
- from 20 pcs €20.24
- from 30 pcs €19.80
Holds a TC2030-NL cable permanently against the target board — 3-pack.
- from 1 pcs €14.00
- from 20 pcs €12.88
- from 30 pcs €12.60
Demo board carrying every Tag-Connect footprint size, for comparison before laying out your own board — 6-, 10- and 14-pin, each with and without legs, plus the EC-10 Edge-Connect™ footprint.
- from 1 pcs €2.00
Related products
Connects a 6-pin Plug-of-Nails™ target (legged) via an RJ12 modular connector to a Microchip ICD programmer.
- from 1 pcs €50.00
Like TC2030-MCP — six contacts on the board, RJ12 modular plug at the programmer — but 254 mm (10″) instead of the standard length.
- from 1 pcs €50.00
- from 20 pcs €46.00
- from 30 pcs €45.00
Connects a 6-pin Plug-of-Nails™ target (no legs) via an RJ12 modular connector to a Microchip ICD programmer. Footprint barely bigger than an SMT resistor.
- from 1 pcs €50.00
Connects a 6-pin Plug-of-Nails™ target (legged) to Microchip's PICkit 3/4/5, via a 6-pin 2.54 mm (0.1″) SIP header.
- from 1 pcs €48.00
Connects a 6-pin Plug-of-Nails™ target (no legs) to Microchip's PICkit 3/4/5 — through a single-row 6-pin header on 2.54 mm (0.1″). Footprint barely bigger than an SMT resistor.
- from 1 pcs €48.00
Hersteller: Tag-Connect, LLC, 433 Airport Blvd, Suite 323, Burlingame, CA 94010, USA. Tel. +1 877-244-4156 · support@tag-connect.com
Verantwortliche Person in der EU (Art. 19 GPSR, da Hersteller ohne EU-Niederlassung):
Collion GmbH & Co.KG
Am Schmiedlacker 56, D-84028 Landshut
Tel. +49 (871) 2066-1000 · info@collion.de