TC2050-IDC-NL-050-STDC14 · Cable for STLINK-V3
€66.00
- From 1 pcs: €66.00 / pc
- From 20 pcs: €60.72 / pc
- From 30 pcs: €59.40 / pc
Available, delivery time: 1-3 days
More than 5 in stock
Product information "TC2050-IDC-NL-050-STDC14 · Cable for STLINK-V3"
Short description
10-pin Plug-of-Nails™ cable, no legs, with a 14-pin 1.27 mm (0.05″) ribbon connector in STDC14 format for STLINK-V3/STLINK-V3MINI.
Connections
| Side | Pins | Connector | Pitch |
|---|---|---|---|
| Board (Tag-Connect) | 10 | Footprint TC2050, no Legs | 1.27 mm (0.05″) |
| Debugger | 14 | Socket STDC14 (FTSH-107 style), 2 × 7 | 1.27 mm (0.05″) |
Pin assignment: TC2050 1–10 to STDC14 3–12; pins 1, 2, 13 and 14 not connected — the full table is in the "Technical data" tab.
Compatible: ST-LINK V3, V3MINI and V3SET, and other debuggers with a 14-pin 1.27 mm connector (STDC14, FTSH-107 style).
Not, or not directly, compatible
- 14-pin, 2 × 7, 2.54 mm (0.1″) — TI MSP-FET430: TC2050-IDC-NL-430
- 20-pin, 2 × 10, 2.54 mm (0.1″) — ARM connector, e.g. SEGGER J-Link, Keil ULINK, ST-LINK/V2: through the adapter board COLL-ARM20-14P-050
- 10-pin, 2 × 5, 1.27 mm (0.05″) — Cortex connector, e.g. Keil ULINK2: TC2050-IDC-NL-050-ALL
- 10-pin, 2 × 5, 2.54 mm (0.1″) — e.g. PEmicro Multilink, USB-Blaster: TC2050-IDC-NL
Easily confused: The ST-LINK/V2 and the older ST-LINKs carry a 20-pin 2.54 mm connector, not this one.
Technical data
- Version: no legs
In use with these devices
STLINK-V3SET (ST STM32, JTAG/SWD) · STLINK-V3 (ST STM32, JTAG/SWD) · STLINK-V3MINI (ST STM32, JTAG/SWD)
What counts is the connector, not the device name: compare the connector on your device with the table above. If it carries a different one, the route goes through an adapter board.
| Bauform: | IDC-Kabelende, Legged |
|---|
Pin assignment
| STDC14 | Signal | TC2050 |
|---|---|---|
| 3 | T_VCC | 1 |
| 4 | T_SWDIO | 2 |
| 5 | GND | 3 |
| 6 | T_SWCLK | 4 |
| 7 | GND | 5 |
| 8 | T_SWO | 6 |
| 9 | T_JRCLK | 7 |
| 10 | T_JTDI | 8 |
| 11 | GNDDETECT | 9 |
| 12 | T_NRST | 10 |
Not connected: 1, 2 (reserved by ST), 13, 14 (Virtual COM Port).
The range — TC2050 1 to 10 onto STDC14 3 to 12 — is the manufacturer specification. Which signal sits on which STDC14 pin is ST’s assignment; it is documented in our schematic for the COLL-ARM20-14P-050.
Pin assignment as specified by the manufacturer.
Accessories
Protective cap for the 10-pin TC2050 cable family (Plug-of-Nails™). Protects spring contacts, steel guide pins and — where present — retention tabs during storage and transport.
- from 1 pcs €5.00
- from 20 pcs €4.60
- from 30 pcs €4.50
Temporarily holds a TC2050-NL cable in place on the target board — for hands-free programming or debugging where board space is tight. 3-pack.
- from 1 pcs €22.00
- from 20 pcs €20.24
- from 30 pcs €19.80
Holds a TC2050-NL cable permanently against the target board — 3-pack.
- from 1 pcs €14.00
- from 20 pcs €12.88
- from 30 pcs €12.60
Demo board carrying every Tag-Connect footprint size, for comparison before laying out your own board — 6-, 10- and 14-pin, each with and without legs, plus the EC-10 Edge-Connect™ footprint.
- from 1 pcs €2.00
- from 20 pcs €1.84
- from 30 pcs €1.80
Adapter board from the 20-pin ARM debugger connector (2 × 10 pin, 2.54 mm) to the 14-pin 1.27 mm (0.05″) connector (1.27 mm) used by the ST-LINK V3 and by Tag-Connect's STDC14 cables. The debug lines run through series resistors; every signal is brought out individually for probing.
- from 1 pcs €30.00
Related products
Ten-pin debug and programming cable with spring pins that lands straight on the board — no connector on the target, just ten contact pads and six holes. The four legs hold it there while you work. At the other end, a standard 2.54 mm (0.1″) ribbon header that fits nearly every debugger.
- from 1 pcs €40.00
- from 20 pcs €36.80
- from 30 pcs €36.00
Ten-pin debug and programming cable with spring pins, without legs — the smallest debug access a board can have: ten contact pads and three holes, nothing else. At the other end a standard 2.54 mm (0.1″) ribbon header.
- from 1 pcs €40.00
- from 20 pcs €36.80
- from 30 pcs €36.00
10-pin Plug-of-Nails™ cable (legged) to 1.27 mm (0.05″) pitch ribbon, for ULINK2 and similar debuggers with Samtec FTSH-105-01 style micro-headers. All 10 pins connected (unlike the standard TC2050-IDC-050, which leaves pins 5/9 open for ARM compatibility).
- from 1 pcs €65.00
- from 20 pcs €59.80
- from 30 pcs €58.50
Like TC2050-IDC-NL-050, but with all 10 pins connected instead of leaving pins 5/9 open. No legs, for ULINK2 and similar debuggers with Samtec FTSH-105-01 style micro-headers on 1.27 mm (0.05″).
- from 1 pcs €65.00
- from 20 pcs €59.80
- from 30 pcs €58.50
6-pin TC2030 cable, legged, for STM32 targets with STLINK-V3/STLINK-V3MINI. 14-pin ribbon connector on 1.27 mm (0.05″) in STDC14 (FTSH-107) format, carries SWD including the SWO signal.
- from 1 pcs €50.00
- from 20 pcs €46.00
- from 30 pcs €45.00
6-pin TC2030-NL cable, no legs, for STM32 targets with STLINK-V3/STLINK-V3MINI. 14-pin ribbon connector on 1.27 mm (0.05″) in STDC14 (FTSH-107) format, carries SWD including the SWO signal.
- from 1 pcs €50.00
- from 20 pcs €46.00
- from 30 pcs €45.00
Edge-Connect™ cable with six contacts at the board edge, terminating in the
- from 1 pcs €85.00
Edge-Connect™ cable with ten contacts at the board edge, terminating in the
- from 1 pcs €88.00
Hersteller: Tag-Connect, LLC, 433 Airport Blvd, Suite 323, Burlingame, CA 94010, USA. Tel. +1 877-244-4156 · support@tag-connect.com
Verantwortliche Person in der EU (Art. 19 GPSR, da Hersteller ohne EU-Niederlassung):
Collion GmbH & Co.KG
Am Schmiedlacker 56, D-84028 Landshut
Tel. +49 (871) 2066-1000 · info@collion.de