TC2050-IDC-NL-050-ALL · 10-Pin Cable, No Legs
€65.00
- From 1 pcs: €65.00 / pc
- From 20 pcs: €59.80 / pc
- From 30 pcs: €58.50 / pc
Available in 7 days, delivery time 1-3 days
Product information "TC2050-IDC-NL-050-ALL · 10-Pin Cable, No Legs"
Short description
Like TC2050-IDC-NL-050, but with all 10 pins connected instead of leaving pins 5/9 open. No legs, for ULINK2 and similar debuggers with Samtec FTSH-105-01 style micro-headers on 1.27 mm (0.05″).
Connections
| Side | Pins | Connector | Pitch |
|---|---|---|---|
| Board (Tag-Connect) | 10 | Footprint TC2050, no Legs | 1.27 mm (0.05″) |
| Debugger | 10 | Socket, 2 × 5 | 1.27 mm (0.05″) |
Pin assignment: contact n is on connector pin n — the cable is wired straight through.
Compatible: debuggers with a 10-pin 1.27 mm pin header.
Not, or not directly, compatible
- 10-pin, 2 × 5, 2.54 mm (0.1″) — e.g. PEmicro Multilink, USB-Blaster: TC2050-IDC-NL
- 14-pin, 2 × 7, 1.27 mm (0.05″) — STDC14, e.g. ST-LINK V3: TC2050-IDC-NL-050-STDC14
- 14-pin, 2 × 7, 2.54 mm (0.1″) — TI MSP-FET430: TC2050-IDC-NL-430
Easily confused: The 10-pin 2.54 mm box header has the same pin count at twice the pitch.
Important note (Atmel-ICE)
Atmel-ICE's 10-pin connectors have reversed, non-standard pin numbering — the LEMTA variant with a reversed ribbon connector compensates for this.
Technical data
- Version: no legs, all 10 pins connected
In use with these devices
ARM Cortex (JTAG/SWD) · Cypress PSoC/MCU (via Miniprog 3 & 4) · Atmel AVR (JTAG/SPI/PDI/μPDI/aWire/debugWIRE) · SAM ARM devices (JTAG/SWD) · ULINK2
What counts is the connector, not the device name: compare the connector on your device with the table above. If it carries a different one, the route goes through an adapter board.
Variants
TC2050-IDC-050-ALL — legged. TC2050-PGUSB — USB variant.
| Form Factor: | IDC-Kabelende, NL (No Legs) |
|---|
Accessories
Protective cap for the 10-pin TC2050 cable family (Plug-of-Nails™). Protects spring contacts, steel guide pins and — where present — retention tabs during storage and transport.
- from 1 pcs €5.00
Temporarily holds a TC2050-NL cable in place on the target board — for hands-free programming or debugging where board space is tight. 3-pack.
- from 1 pcs €22.00
Holds a TC2050-NL cable permanently against the target board — 3-pack.
- from 1 pcs €14.00
Demo board carrying every Tag-Connect footprint size, for comparison before laying out your own board — 6-, 10- and 14-pin, each with and without legs, plus the EC-10 Edge-Connect™ footprint.
- from 1 pcs €2.00
Storage case for Tag-Connect cables and accessories — the same one as in the TC2050 evaluation kit. Grey plastic case with carrying handle, a foam insert with compartments inside and convoluted foam in the lid. Room for one or two cables together with accessories such as an adapter, clip or grip.
- from 1 pcs €19.00
Related products
Ten-pin debug and programming cable with spring pins that lands straight on the board — no connector on the target, just ten contact pads and six holes. The four legs hold it there while you work. At the other end, a standard 2.54 mm (0.1″) ribbon header that fits nearly every debugger.
- from 1 pcs €40.00
- from 20 pcs €36.80
- from 30 pcs €36.00
Ten-pin debug and programming cable with spring pins, without legs — the smallest debug access a board can have: ten contact pads and three holes, nothing else. At the other end a standard 2.54 mm (0.1″) ribbon header.
- from 1 pcs €38.00
- from 3 pcs €37.00
- from 5 pcs €36.00
10-pin Plug-of-Nails™ cable (legged) to 1.27 mm (0.05″) pitch ribbon, for ULINK2 and similar debuggers with Samtec FTSH-105-01 style micro-headers. All 10 pins connected (unlike the standard TC2050-IDC-050, which leaves pins 5/9 open for ARM compatibility).
- from 1 pcs €65.00
- from 20 pcs €59.80
- from 30 pcs €58.50
10-pin Plug-of-Nails™ cable, no legs, with a 14-pin 1.27 mm (0.05″) ribbon connector in STDC14 format for STLINK-V3/STLINK-V3MINI.
- from 1 pcs €66.00
6-pin TC2030 Plug-of-Nails™ cable, legged, for ARM Cortex targets. 10-pin ribbon connector on 1.27 mm (0.05″) in FTSH-105 format (Cortex Debug standard, e.g. Keil ULINK2).
- from 1 pcs €45.00
6-pin TC2030-NL Plug-of-Nails™ programming cable, no legs, for ARM Cortex targets. 10-pin ribbon connector on 1.27 mm (0.05″) in FTSH-105 format, saves over 66% board area versus classic FTSH-105 micro-headers.
- from 1 pcs €45.00
6-pin TC2030-NL Plug-of-Nails™ cable, no legs, for ARM Cortex targets — with the 10-pin 1.27 mm (0.05″) ribbon connector fitted reversed at the factory, specifically for Atmel-ICE.
- from 1 pcs €50.00
Edge-Connect™ cable with six contacts at the board edge, terminating in the **ARM Cortex debug connector** — the 10-pin 1.27 mm (0.05″) header carried by Keil ULINK2 and most Cortex debuggers.
- from 1 pcs €85.00
Hersteller: Tag-Connect, LLC, 433 Airport Blvd, Suite 323, Burlingame, CA 94010, USA. Tel. +1 877-244-4156 · support@tag-connect.com
Verantwortliche Person in der EU (Art. 19 GPSR, da Hersteller ohne EU-Niederlassung):
Collion GmbH & Co.KG
Am Schmiedlacker 56, D-84028 Landshut
Tel. +49 (871) 2066-1000 · info@collion.de